Bedliner Removal: How to Remove or Re-Coat a Liner
Heat, strippers, discs and blasting for spray-in, roll-on and drop-in liners, what each costs, how to work safely, and when repairing or re-coating beats stripping.

Start a spray-on bedliner business
Spray bedliners for a living.
ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.
- $0
- franchise fees or royalties
- 35+
- years in business
- 50+
- countries with applicators
- 24/7
- technical support
Bedliner is built not to come off, which is exactly what makes removing it hard. The right method depends on the type of liner, whether it's still bonded, and whether you need bare metal or just a sound surface for a new coat.
A drop-in lifts out. A thin roll-on usually comes off with heat or a stripper that lists polyurethane, a scraper, then 36–80 grit discs. A professional spray-in, often around 1/8 inch thick, needs heat and scraping plus discs, or shop blasting at roughly $1–$5 per sq ft. If most of it is still bonded, scuffing and re-coating is usually cheaper. Find your method or compare the costs.
Who's writing: ArmorThane makes ArmorLiner spray polyurea in Springfield, Missouri, and trains the applicators who spray it. We'd rather you keep a sound liner than strip it, and this guide says so where it applies. Bedliner removal is slow, messy work, so it is worth knowing which liner you have before you start. In many cases bedliner removal is not needed at all.
- 1Which liner do you have?
- 2Remove, repair or re-coat?
- 3Removal method finder (interactive)
- 4Removal methods compared
- 5How to remove a spray-in liner
- 6Removing roll-on liner and bedliner paint
- 7Taking out a drop-in liner
- 8Media blasting and shop costs
- 9Safety: heat, fumes, dust and strippers
- 10Remove vs re-coat calculator (interactive)
- 11Repairing and re-coating an old liner
- 12Bedliner removal FAQ
Which liner do you have?
Three different products all get called "bedliner," and each comes out differently.
| Type | What it is | Thickness | How it's held | Removal |
|---|---|---|---|---|
| Professional spray-in | Polyurea or polyurethane/polyurea hybrid (LINE-X, Rhino, Speedliner, ArmorLiner) | About 125 mils (1/8 in) on the floor; DeFelsko cites 125–250 | Bonded to scuffed paint or bare metal; Rhino calls it permanent | Hardest |
| Roll-on or DIY kit | Urethanes and acrylics (Herculiner, Raptor, Rust-Oleum, Dupli-Color) | About 10–40 mils in two coats for most kits | Bonded to scuffed paint; strength depends on prep | Moderate |
| Drop-in | Thermoformed plastic shell (Penda and many factory liners) | Penda: 0.19–0.2 in HDPE | Sits in the bed, sometimes with screws or clips | Easiest |
How to tell: look at an edge at the tailgate or rail. A drop-in has a visible gap and lifts away. A sprayed or rolled liner has no gap and runs continuously into the corners. At a chip, a pro spray-in shows a thick, rubbery layer; a roll-on is a much thinner film.
Remove, repair or re-coat?
Many beds don't need stripping at all. ArmorThane's spray-in bedliner cost guide puts it this way: "a sound old spray-in liner can often be scuffed and sprayed over; a peeling one has to be removed, which is slow." So the deciding question is whether the liner is still bonded.
Fix the damage
- Gouges, cracks or a worn-through spot
- The rest is firmly bonded
- Cut back, scuff, clean and patch
Spray or roll over it
- Faded, scratched or thin, but bonded
- Loose only in spots you can cut back
- Little or no removal work
Strip it out
- Peeling across much of the bed
- Rust bubbling up under it
- You need bare metal for bodywork
A quick bond check
Work a putty knife under the liner at chips, torn edges and rust bubbles. If it lifts only at the damage and holds firm beyond it, the liner is bonded. If it peels back in sheets, that area has to come off. Start at the edges: Rhino's applicator tips call unsealed or poorly prepped edges "a common starting point for peeling and delamination."
Rust under a liner means the bond has already failed there, so the liner around it comes off to clean metal first; see our truck bed rust repair guide. Not sure what you're looking at? An ArmorThane-certified applicator can check the bed and tell you whether it can be sprayed over. Get a free bedliner quote.
Bedliner removal method finder
Pick the liner, its condition, how much you're dealing with and the tools you own. The finder suggests a method, the effort, what you'll spend and the gear to wear.
How should I get this liner out?
Based on manufacturers' guidance, cost guides and owner reports cited on this page. Shop prices use general sandblasting rates, not bedliner quotes.
Peeling spray-in liner, DIY. Work warm (cold liner is more brittle), score it into strips, heat one strip at a time without scorching it and scrape at a low angle; Durabak warns a steep chisel can dent the bed. Finish with 36–80 grit discs and expect repeated passes. For comparison, a shop at general sandblasting rates ($1–$5 per sq ft, HomeGuide) would charge about $70–$350 for 70 sq ft.
Bed areas are our estimates from kit makers' coverage figures; rails add about 15 sq ft. Our truck bed dimensions guide gives exact sizes.
Bedliner removal methods compared
Every method trades your time against money and risk to the truck. Heat and scraping take the bulk off, discs finish the job, strippers suit thin films, and blasting or induction heat moves the job to a shop.
| Method | Best for | Cash cost | Risk to the truck | Hazards |
|---|---|---|---|---|
| Heat gun and scraper | Spray-in and roll-on, large areas | Heat gun from $25 (Wagner HT1000, 750°F and 1,000°F) | Scorched paint; dents if the chisel is held steep (Durabak) | Fumes if the liner scorches |
| Induction heater and putty knife | Spray-in on steel | Shop tool; no price published | Heats the steel; body filler complicates it | Heat; gloves and goggles |
| Chemical stripper | Roll-on films and residue | Stripper, plastic sheet, scrapers | Strips paint too; test first | Solvent fumes, skin, eyes |
| Wire wheel or 36–80 grit disc | The last layer, bare metal | Discs for a grinder or DA sander | Removes paint; gouges if you dig in | Dust, flying debris, noise |
| Media blasting (shop) | Whole beds, bare-metal jobs | $1–$5 per sq ft or $45–$80 an hour, general rates | Depends on media and operator | Contained at the shop |
| Dry ice blasting | Untested on bedliner in reports we found | $3.50–$5 per sq ft | Unknown for liners | Contained at the shop |
Rhino Linings is candid: its liner is "designed to provide permanent protection," and "While removal is technically possible, it is not the intended use of the product." Durabak, which sells a brush-on liner, warns that once you've bought equipment and chemicals, doing it yourself can cost close to what a pro charges. Induction Innovations says its heaters warm the steel "and release the bonding properties of adhesives and coatings," and claims the method is "500% faster than using expensive consumables." That's a vendor claim with no published test, but it's worth asking local shops whether they have one.
How to remove a spray-in bedliner
This works for LINE-X, Rhino, Speedliner, ArmorLiner and other sprayed liners, and it's how to remove Rhino liner from rockers and bumpers too, though painted panels need extra care.
Decide how far you're going
Cutting loose liner back to a firm edge is a small job next to taking a bonded liner to bare metal. Run the remove vs re-coat calculator first.
Protect the truck and work warm
Tape off paint and lights. Overland Truck notes cold liners are "harder and more brittle," so a heated garage helps.
Score, heat and scrape
Score the liner into strips with a utility knife, as Induction Innovations does before heating. Warm one strip at a time, keep the gun moving so the liner softens without scorching, and scrape with the blade held low: Durabak warns a steep chisel can dent the bed.
Finish with discs
Overland Truck uses 36–80 grit discs on a DA or angle sander. One TacomaWorld owner found a wire wheel removed liner faster, while an abrasive disc reached bare metal sooner but wore out faster.
Clean, treat rust and protect the metal
Degrease, wire-wheel any rust, wash and dry, as our rust repair guide describes, then prime or line the bare steel promptly.
Removing roll-on liner and bedliner paint
Roll-on kits and bedliner "paint" build a far thinner film than a professional spray, so there's less to remove. Chemistry varies: Herculiner is a solvent-based polyurethane with rubber granules, Rust-Oleum's Truck Bed Coating a water-based acrylic, and Raptor a two-part polyurethane. One stripper won't suit them all.
The stripper route
- Choose a methylene chloride-free remover that lists polyurethane. Klean-Strip's Premium Stripper "strips paint, epoxy and polyurethane from wood, metal and masonry."
- Test a patch first; Dumond calls testing "critical."
- Follow the label's dwell time. Durabak suggests 5–15 minutes for the removers it names; Jasco says its remover strips multiple layers in 15 minutes.
- Scrape, repeat, then wash off as the label directs.
The heat and disc route
- Durabak lists a heat gun and chisel as one route: soften a section, then scrape at a low angle.
- Some owners go straight to discs; one TacomaWorld owner planned a wire wheel for his 20-year-old peeling Herculiner.
- Finish with 36–80 grit, then degrease before any new coating.
If the roll-on is still bonded, don't strip it; scuff it and roll on another coat. Herculiner says to paint over its liner with polyurethane-based paint (never lacquer) within 24 hours of it drying to the touch, or lightly sand and clean it after that. See spray-on liners vs DIY kits for why many roll-on jobs end up at a spray-in shop.
Bedliner on painted panels. On fenders, rockers or overspray on a cab, a stripper that lifts the liner lifts paint too. Test in a hidden spot, and for fresh overspray on good paint, ask a body shop first.
Taking out a drop-in liner
A drop-in is the easy one. Penda says its liners take "about 5-15 minutes to install," and removal is mostly the reverse: take out any screws or clips at the front wall, rails or tailgate cap, then lift it out with a helper.
The reason to pull one is often what's underneath. A drop-in that doesn't fit well can "allow debris and water to get underneath it," as ArmorThane's drop-in vs spray-on comparison puts it, and LINE-X notes pre-formed liners "can shift around." Penda builds in a feature that "allows water to drain from the bed." Either way, wash and dry the bed, check for worn paint and rust, and treat rust before the bed is covered again. ArmorThane's cost guide lists replacement drop-ins at $200–$500, roll-on kits at $110–$165 and pro spray-in liners at $470–$800.
Media blasting and shop costs
ArmorThane's surface preparation guide calls abrasive blasting "highly effective at removing rust, old coatings, scale." We found no published price for blasting a bedliner, so these are general sandblasting rates: use them to sanity-check a quote.
Per sq ft; bars show the high end. HomeGuide (Jun. 2024); Fixr (Jan. 2025) gives the same dry ice range.
| Media | Price per lb | Notes |
|---|---|---|
| Glass bead | $0.50–$2.50 | Fixr: $800–$1,100 to blast a car shell |
| Walnut shell | $1.00–$1.30 | Crushed nut shells |
| Baking soda | $1.50–$2.50 | Same range from HomeGuide and Fixr |
| Aluminum oxide | $2.00–$3.00 | Named in ArmorThane's prep guide |
| Plastic media | $3.00–$6.00 | Fixr: $550–$750 to blast a car shell |
By our arithmetic, a 70 sq ft bed comes to roughly $70–$350 at $1–$5 per sq ft; HomeGuide lists labor at $45–$80 an hour, up to $300 for complex work. Expect minimum charges and ask for a fixed price. A bedliner shop can quote removal and the new liner together; find one with the bedliner applicator finder.
Heat, fumes, dust and strippers
Strippers
The EPA banned methylene chloride for consumer paint and coating removal in 2019, and its 2024 rule extends that to all consumer uses and most commercial paint removers. Today's removers still carry warnings; Klean-Strip's include California Prop 65 notices for ethylbenzene. Read the label and ventilate.
Gear list
- Respirator: for fumes, stripper vapor and dust
- Eyes and face: goggles, plus a face shield for wheels and discs
- Gloves: heat-resistant for heat, chemical-resistant for strippers
- Coveralls: Durabak recommends them with a mask
Remove vs re-coat cost calculator
Compare stripping the whole bed and relining it with cutting back only the loose areas and re-coating the rest. Enter your own hours: nobody publishes a standard removal time.
Should I strip my bedliner or re-coat it?
New-liner prices from ArmorThane's spray-in bedliner cost guide; shop removal at HomeGuide's general $1–$5 per sq ft sandblasting rate.
Re-coat over it. Only about 15% is loose, so cutting that back and re-coating the sound remainder skips most of the removal work. Full removal here is 12 hours at $20 an hour plus $100 in supplies. We price a spray-over at the same $470–$800 as a new pro liner (ArmorThane cost guide), because it is still a full liner, so the gap between the two paths is the removal work: about $289.
Published ranges and your inputs, not a quote. The 50% cut-off for removing everything is our rule of thumb.
Repairing and re-coating an old liner
Spray-in bedliner repair is routine for liner shops. LINE-X says "Small scratches or chips can usually be fixed with a touch-up application," and for bigger damage pros "sand down the affected area and reapply the bedliner." Rhino offers repair formulations, Speedliner will "Recoat or repair any professionally sprayed-in polyurethane or polyurea bed liner," and LINE-X ReNew "Adheres to any existing polyurethane and polyurea coating."
How a spray-over is prepped
- Cut back loose liner to a firm, tapered edge; take rust to clean metal.
- Scuff the old liner: Speedliner starts with "Rough up the surface"; Durabak uses 60-grit.
- Clean and dry with solvent: Durabak names xylene, Rhino wipes sanded edges with acetone.
- Prime: Speedliner uses Primer450; Rhino uses an adhesion promoter on existing liners.
- Spray and cure: Speedliner quotes "1-2 days."
DIY patches and faded liners
DoItYourself.com's patch method: wash, dry, scuff around the damage, apply repair material 1–2 inches beyond it and let it cure 2–3 days. One vendor's half-gallon polyurea-hybrid repair kit costs $75.55 and claims to bond to polyurea, polyurethane, urethane and acrylic liners.
A chalky but bonded liner needs a topcoat, not removal: Rhino Shine Ultra, LINE-X ReNew and ArmorThane's STS ColorCoat, an aliphatic polyurethane topcoat matched to an OEM paint code, all go over existing liners. See our bedliner colors guide.
Prep is what makes a re-coat hold. ArmorThane's polyurea guide says surface preparation "accounts for 60-80% of coating system success" and recommends an adhesion test on a patch before a full job.
Repairs, re-coats and relines are all paid work.
Every owner with a peeling liner needs someone who can strip it, patch it or spray over it. ArmorThane supplies ArmorLiner polyurea and spray equipment and trains your crew through certification. Turnkey systems start at $25,000 with equipment, training, first chemical, prep and safety gear. No franchise fee, dealership fee or royalty.
Third-party financing available. See applicator opportunities →
Re-coat or reline with ArmorLiner polyurea
ArmorLiner is a two-component, 1:1, 100% solids, fast-set polyurea. ArmorThane-certified applicators spray it over properly prepared beds, whether that's a scuffed and primed old liner or a bed taken back to metal. ArmorThane has made coatings since 1989 and supplies applicators in more than 50 countries.
A good applicator will tell you if your liner only needs a repair. Use the applicator finder to reach one near you, read about ArmorLiner, and join the newsletter for new bedliner guides.

Bedliner removal FAQ
What is the easiest way to remove a spray-in bedliner?
There isn't an easy way; Rhino calls its liner permanent and says removal isn't the intended use. The least effort for you is a shop with media blasting or an induction heater. Doing it yourself, score the liner into strips, soften each with a heat gun, scrape at a low angle and finish with 36–80 grit discs.
How do you remove Rhino liner or LINE-X?
Like any professional spray-in: heat and scrape, then sand, or have a shop blast it. Rhino says removal is technically possible but not the intended use, and one TacomaWorld owner says LINE-X suggested a hammer, a chisel and a dual-action sander. If the liner is only faded or damaged, ask a liner shop about a repair first.
Can you remove bedliner without damaging the paint?
Usually not. Applicators scuff the paint before spraying so the liner bonds, and heat, strippers, discs and blasting will mark or remove what's left. In a bed that rarely matters, because it gets relined. On body panels, rockers or bumpers, plan on refinishing and get a body shop quote before you start.
Will paint stripper remove bedliner?
It can lift thinner roll-on liners, but no stripper we found names bedliner on its label. Use a methylene chloride-free remover that lists polyurethane, such as Klean-Strip's Premium Stripper, test a patch and follow the label's dwell time. Thick professional liners usually need heat and scraping instead. Strippers remove paint, too.
Does a heat gun work to remove bedliner?
Yes. Heat is the usual way to loosen a spray-in liner so it can be scraped. A basic heat gun such as Wagner's HT1000, with 750°F and 1,000°F settings, costs about $25. Soften the liner without scorching it: OSHA lists thermal degradation of polyurethane as a source of isocyanate exposure. Ventilate and wear a respirator.
How much does it cost to remove a bedliner?
A drop-in costs nothing to remove. DIY removal of a sprayed liner costs your time plus a heat gun (from about $25), discs and stripper. General sandblasting runs $1–$5 per sq ft or $45–$80 an hour (HomeGuide), roughly $70–$350 for a 70 sq ft bed before minimums. Ask a shop for a fixed quote.
Can you spray a new bedliner over an old one?
Often, if the old liner is still bonded. ArmorThane's cost guide notes a sound old spray-in can often be scuffed and sprayed over, while a peeling one has to be removed. Shops cut back loose areas, scuff, solvent-clean, prime and spray. LINE-X ReNew and Speedliner both advertise recoating existing polyurethane and polyurea liners.
How do you repair a spray-in bedliner that is peeling or gouged?
Cut loose liner back to a firm edge, scuff and clean the area, then patch it and blend the texture. DoItYourself.com's method applies repair material 1–2 inches beyond the damage and lets it cure 2–3 days. LINE-X says small chips can usually be touched up. Widespread peeling means removal.
How do you remove a roll-on bedliner like Herculiner?
Roll-on films are much thinner than pro liners, about 10–40 mils for most kits, so there is less to take off. Use heat and a scraper or a methylene chloride-free stripper that lists polyurethane, then 36–80 grit discs. If it is still bonded, scuff it and recoat instead of stripping it.
How do you take out a drop-in bed liner?
Remove any screws or clips at the front wall, rails or tailgate cap, then lift it out with a helper. Penda says its drop-ins take about 5–15 minutes to install, so removal is quick. Then wash and inspect the bed, since a poorly fitting drop-in can trap water and debris, and treat any rust.
Can you paint over bedliner?
Yes, with the right prep. Herculiner says to use polyurethane-based paint, not lacquer, within 24 hours of its liner drying to the touch, and to lightly sand and clean it after that. For professional liners, UV topcoats such as LINE-X ReNew or ArmorThane's STS ColorCoat are made to go over an existing liner.
Is it dangerous to grind or burn off bedliner?
It can be without protection. OSHA links the thermal degradation of polyurethane to isocyanate exposure and occupational asthma. Grinding throws dust and debris, and strippers carry label warnings. Soften the liner rather than burning it, ventilate, and wear a respirator, eye and face protection, gloves and coveralls.
Written from liner makers' FAQs and repair pages, stripper and tool makers' product pages, EPA and OSHA guidance, dated cost guides, owner reports and decades of making spray polyurea. Reviewed September 27, 2026.
Methodology and sources
Prices as published, read September 2026. Blasting rates are general sandblasting figures, not bedliner quotes. Bed areas are our estimates from kit coverage. The calculator prices a spray-over at the same range as a new liner and scales DIY removal to the loose share; both are our assumptions. Owner reports are individual forum posts.
- Rhino Linings, FAQ: rhinolinings.com
- Rhino Linings, 12 Best Tips for Spraying Top Notch Rhino Liners (Jul. 2025, updated Jun. 2026): rhinolinings.com
- LINE-X, ReNew Bedliner Repair: linex.com
- LINE-X, Should You Line Your Truck Bed with a Spray-On Bedliner? (Nov. 2024): linex.com
- Speedliner, Liner Repairs: speedliner.com
- Durabak Company, How to Remove Bed Liner (Feb. 2018): durabakcompany.com
- Overland Truck, Remove Bedliner from Truck (Oct. 2025): overlandtruck.com
- Induction Innovations, Removing Spray-In Bedliner (Nov. 2024): theinductor.com
- TacomaWorld, Tips and tricks to remove old bed liner (Apr. 2022): tacomaworld.com
- U.S. EPA, Risk Management for Methylene Chloride: epa.gov
- OSHA, Isocyanates: osha.gov
- Klean-Strip, Premium Stripper (non-methylene chloride): kleanstrip.com
- Jasco, Premium Paint and Epoxy Remover: jasco-help.com
- Dumond, Smart Strip Advanced: dumondglobal.com
- Wagner SprayTech, HT1000 Heat Gun: wagnerspraytech.com
- HomeGuide, Sandblasting Cost (Jun. 2024): homeguide.com
- Fixr, Sandblasting Cost (Jan. 2025): fixr.com
- Penda, FAQs: penda.com
- DoItYourself, How to Repair Sprayed On Truck Bed Liner: doityourself.com
- Spray Lining and Coatings, Truck Bedliner Repair and Renew Kit: sprayliningandcoatings.com
- Herculiner FAQs, Rust-Oleum and U-POL Raptor data sheets (kit chemistry): herculiner.com
- DeFelsko, Measuring Spray-on Truck Bedliner Thickness: defelsko.com
- ArmorThane, Spray-In Bedliner Cost (Sep. 2026), Polyurea Guide (Mar. 2026), Which Truck Bedliner Is Better and truck bed rust repair: armorthane.com
Bedliner fixes and prices in your inbox.
Repair, removal and re-coat guides, plus spray-in price updates, from the people who make ArmorLiner polyurea.
- New bedliner repair and removal guides
- Spray-in and DIY cost updates
- Custom truck and vehicle projects
Heavy-Duty Coatings for Vehicles & Equipment
Flip through the whole brochure right here, or open it full screen on Issuu to share it.
Don't strip what you can save. Don't save what's peeling.
A sound liner can often be scuffed and sprayed over; a peeling one has to come off. ArmorThane-certified applicators can tell you which you have and spray ArmorLiner polyurea over a properly prepared bed. Contractors: we train applicators with no franchise fee, dealership fee or royalty.
Old liner peeling or worn out? Get a quote to repair, re-coat or replace it.
Tell us your truck, your bed size and what the old liner is doing. We'll connect you with an ArmorThane-certified applicator who can tell you whether it needs a repair, a spray-over or full removal, and price the job.
- A straight answer on repair vs removal
- Seamless ArmorLiner polyurea spray-in liners
- Prep and rust repair before the new liner
- Own a shop? Ask about becoming a bedliner applicator
More to read on bedliners and vehicles
Short reads from ArmorThane on Issuu. Tap one to open it right here.
More in Automotive & marine
Automotive & marineMilitary Vehicles
Automotive & marineOverland Trailer Coatings
Automotive & marinePontoon Boat Flooring
Automotive & marineRoll-On Bedliner
Automotive & marineRV Insulation
Automotive & marineRV Roof Franchises & Alternatives
Automotive & marineRV Roof Replacement Cost
Automotive & marineRV Roof Replacement Near Me








