Pontoon Boat Flooring Options & Real Costs
Marine vinyl, woven vinyl, carpet, EVA foam, aluminum and spray-on polyurea compared on heat, grip, rot and cleaning, with September 2026 prices by boat length.

Coat boats and docks for a living.
ArmorThane is the one-stop shop for applicators. We make the chemistry, build the equipment, train you hands-on and back you with technical support, with no franchise fees and no royalties. Applicators have come first here since 1989.
- $0franchise fees or royalties
- 35+years in business
- 50+countries with applicators
- 24/7technical support
Pontoon boat flooring takes more abuse than any floor in your house: sun, rain, wet feet, fish and a deck that flexes on every wave. Pick the wrong surface and you'll re-floor. Let water sit on the plywood underneath and you'll re-deck too.
For most owners, the best pontoon boat flooring is marine vinyl or woven vinyl glued to 3/4-inch treated plywood. Rolls cost $10–$42 per running foot, about $230–$925 for a 22-ft deck. Carpet is cheapest but holds water. EVA foam is softest. A sprayed polyurea non skid deck coating is seamless, at about $5–$12 per sq ft installed. Price your deck or find your best fit.
Below, every common option is compared on heat, grip, rot, cleanup and cost, using prices read in September 2026. A word about who's writing: ArmorThane, founded in 1989 and based in Springfield, Missouri, makes polyurea coatings and trains the certified applicators who spray boat decks. We don't make vinyl, carpet or foam, and for many pontoons one of those is the right answer.
- 1Pontoon flooring options compared
- 2Deck cost calculator (interactive)
- 3Marine vinyl vs woven vinyl
- 4Spray-on and roll-on deck coatings
- 5Flooring selector (interactive)
- 6Plywood rot and deck replacement
- 7Costs by boat length and kits
- 8How to replace pontoon flooring
- 9Care and cleaning by material
- 10Pontoon boat flooring FAQ
Pontoon flooring options, compared
Almost every pontoon floor is one of these surfaces over 3/4-inch treated plywood screwed to the aluminum cross-members. Some builders use all-aluminum decks instead, and coatings can go over plywood or aluminum.
| Flooring | Price read Sept. 2026 | Strengths | Watch out for | Life or warranty data |
|---|---|---|---|---|
| Marine carpet | $11.99–$16.99 per ft of roll | Soft, affordable, easy to install | Mildew, stains; "holds moisture like a sponge" | No neutral data found |
| Marine vinyl (solid) | $10.39–$30 per ft of roll | Easy to clean; Harris says it "won't fade" | Warm in high heat; dark colors run hotter | One maker: 2-year prorated warranty |
| Woven vinyl | $17.56–$42 per ft of roll | Soft, textured, power-washable | Costs more; heat claims disputed | One maker: 10-year limited warranty |
| EVA foam (SeaDek-type) | $168–$220 per 22 sq ft sheet | Softest; peel-and-stick; sold on wet grip | Needs a clean, hard surface; pricey | 5–7 years in hard use; 3-year warranty |
| Aluminum deck | Builder option; planks sold as raw extrusions | "NO WOOD and NO ROT" (Veranda) | A structural change, not a floor covering | No neutral data found |
| Spray-on polyurea | About $5–$12 per sq ft installed (floor benchmarks) | Seamless, texture you choose, same-day service | Pro-only; needs sound, primed plywood | 10–20+ years on garage floors (HomeGuide); no boat data |
| Roll-on non-skid | $159.95 per gallon (about 60 sq ft) | Cheap, DIY, adds grip | Thin; long prep; some aren't sealants | Makers claim 10–15 years |
Harris puts foam-backed vinyl on its own pontoons for "value for construction, appearance and maintenance." For aluminum pontoon boat flooring, Veranda builds all-aluminum decks because a "wood deck can hold moisture and increase in weight over time."
Pontoon flooring ideas that work
Teak-look woven vinyl gives an older boat a new-boat look. EVA foam pads at the helm and swim ladder add soft, grippy spots without re-flooring. On fishing and rental boats, set a sprayed deck's texture by zone: lighter where people go barefoot, heavier where they fish. And pick a light color if the boat sits in the sun. The U.S. Department of Energy says conventional roofs can reach 150°F or more on a sunny afternoon while reflective ones stay more than 50°F cooler; a sunny deck follows the same physics.
Pontoon deck cost calculator
Enter your deck size, pick a floor and decide whether the plywood stays. You'll get the square footage, how much to buy, a do-it-yourself material cost and an installed benchmark.
What will my pontoon floor cost?
Prices read September 2026 from flooring retailers, SeaDek, Durabak, a Michigan marine shop and floor-coating cost guides. Deck length is usually close to the boat's nominal length.
187 sq ft deck, marine vinyl. Rolls cover the whole deck, so you buy the full 22 ft: 25-mil MariDeck at $10.39 a foot up to extreme-duty vinyl at about $30 a foot ($479.99 for 16 ft), plus 2 gal of marine adhesive at $40 (about 96 sq ft per gallon, PMI). Installed: one Michigan shop’s $127 per foot of boat to replace the floor with vinyl, $152 with premium vinyl. Prices read September 2026.
Marine vinyl vs woven vinyl
Vinyl pontoon boat flooring means two different products. Solid vinyl is a printed or embossed sheet, often foam-backed, from about 25 to 80 mils. Woven vinyl is PVC-coated yarn on a cushion backing and much thicker: PMI's woven lines are 144 mils.
| Product (seller) | Type | Price per running ft | Specs |
|---|---|---|---|
| MariDeck C25102 (Great Lakes Skipper) | Solid vinyl | $10.39 sale ($12.99) | 25 mil, 102 in wide |
| Tuf-Deck (PMI Marine) | Solid vinyl | $27.00 | 50 mil, 8 ft 6 in; sold for fishing pontoons |
| Extreme Duty vinyl (PontoonStuff) | Solid vinyl | From $479.99 (16 ft), about $30 | 16–28 ft lengths |
| Cobalt, Infinity, Corinthian (Great Lakes Skipper) | Woven vinyl | $17.56 sale ($21.95) | 74 in to 10 ft wide |
| Woven Flexa (Marine Vinyl Fabric) | Woven vinyl | $19.99 thin / $30.99 premium | 102 in; 1.75–3.00 lb per ft; 10-year limited warranty |
| SeaGrass and Teak (PMI Marine) | Woven vinyl | $40.00–$42.00 | 144 mil, foam-backed, 8 ft 6 in |
Which one is hotter?
Nobody has published a neutral test. PMI says its woven "stays cool on the bare foot even in direct sunlight." G-Floor's maker says woven registered 13 degrees hotter than its non-woven vinyl, with no test conditions given. Harris says both can get warm. Color is the one thing physics settles: light surfaces stay cooler.
Pick solid vinyl for fishing, rentals or the lowest price per foot. Pick woven for cruising and swimming. Either way, a glued sheet keeps rain off the plywood better than carpet.
Spray-on and roll-on deck coatings
A non skid deck coating replaces the floor covering with a textured liquid-applied surface. Know which of these three you're being quoted.
| Coating | Thickness and coverage | Seals the deck? | Cost | Cure |
|---|---|---|---|---|
| Spray polyurea (pro) | 60–80 mils typical on floors; 1 gal covers 1,604 sq ft at 1 mil | Yes: one seamless membrane | About $5–$12 per sq ft installed (floor benchmarks) | Tack-free in under 60 seconds; most marine jobs back in service the same day |
| Roll-on polyurethane (Durabak 18) | About 60 sq ft per gal in 2 coats (textured) | A thin film | $159.95 per gal, about $2.67 per sq ft | Light traffic 6–12 h; full cure about 4 days |
| Acrylic non-skid (KiwiGrip) | About 20 sq ft per liter at 2–3 mm | No: "does not act as a sealant" | Retail varies by size | Barefoot in 12–24 h |
What a sprayed pontoon deck gets you
Our marine coating systems are 100% solids, zero-VOC polyureas applied as "seamless, slip-resistant decking over fiberglass, gelcoat, aluminum or plywood." Grit broadcast into the wet film "tunes traction from lightly textured to heavily aggressive." See our non-slip coatings and SureGrip soft polyurea, our highest-friction polyurea. It's the approach behind our lobster boat deck coatings and polyurea houseboat coatings.

Three things to ask before anyone sprays
- Is the plywood compatible? Pontoon plywood sellers say CCA-treated sheets "should not be coated or treated before installation," and one floor-coating maker bars marine plywood entirely. Ask for the coating maker's primer and an adhesion test. Floor-coating makers also call for screws every 6 inches at panel edges, reinforced joints and two primer coats on porous plywood.
- Will it be UV-stable? Aromatic polyurea yellows in sun "without compromising its physical performance" (see what is aromatic polyurea). On a sunny deck, ask for an aliphatic top layer such as color-stable ArmorFlex UV.
- How heavy? At 60 mils, spray polyurea weighs about 0.33 lb per sq ft, close to the 0.35 lb of a premium felt-backed woven vinyl.
Roll-on products have a place too. On a small aluminum fishing boat, a gallon or two of textured roll-on is a fair weekend project; Boating magazine's Durabak deck took two gallons and about 13.5 hours. Our roll-on bedliner guide compares thin films with a sprayed coat. Don't expect one to seal a pontoon deck, though. Spray polyurea itself isn't DIY: its precursors can be dangerous, as we explain in why DIY polyurea is a mistake.
Pontoon flooring selector
Tell us how you use the boat, where it lives and what matters most. The selector weighs each floor on the sourced pros and cons above and explains its pick.
Which flooring fits my pontoon?
A guide, not a guarantee. The weighting is ours; the reasons come from builders, flooring makers and coating data.
Why woven vinyl: Woven vinyl is soft and textured, and Bennington says its switch to woven was “mostly driven by the consumer.” Woven vinyl can be power washed and scrubbed. Runner-up: marine vinyl.
Plywood rot and deck replacement
Pontoon boat flooring replacement often turns into a plywood job when the old vinyl comes up, so walk the deck before you order. Soft or spongy spots, flex between cross-members and bolts that won't stay tight can all point to wet plywood. The usual culprits are carpet holding water against the wood and water seeping up at seams and fastener holes.
3/4 in CCA-treated plywood
CCA-treated Douglas fir marine plywood, 4 ft × 8 ft or 8 ft 6 in, $125–$145.99 a sheet: "the same plywood used on most new pontoon boats." PMI warns copper sulfate alternatives "delaminate within years."
One sheet per 4 ft of deck
Sheets run across the deck, so a 24-ft deck takes six. Pontoon Specialists' plywood kits run $500 (16 × 8 ft) to $810 (24 ft × 8 ft 6 in), plus shipping.
Screws or elevator bolts
At least six self-tapping screws per cross-member where sheets join and five on center cross-members, or three and two elevator bolts (Pontoon Specialists).
Butyl tape at the joints
PMI's butyl deck joint tape ($20 for 50 ft) "prevents water from seeping up between deck boards," the most rot-prone spot on the deck.
Plywood life claims vary: PMI says "rated to last 50 years," PontoonStuff offers a 6-year warranty and Pontoon Specialists a limited lifetime one. Keeping water off it matters more. Rebuilding a small aluminum boat's floor instead? Check the flotation too; boat pour foam should be tested to 33 CFR 183.114, as our two-part pour foam guide explains.
Pontoon flooring cost by boat length
Here's what an 8 ft 6 in wide deck costs at September 2026 prices.
| Deck (8 ft 6 in wide) | Vinyl or woven roll, DIY | New plywood, DIY | Shop vinyl re-floor | Spray polyurea benchmark |
|---|---|---|---|---|
| 16 ft (136 sq ft) | $166–$672 | 4 sheets: $540–$584 | $2,032–$2,432 | $680–$1,632 |
| 18 ft (153 sq ft) | $187–$756 | 5 sheets: $675–$730 | $2,286–$2,736 | $765–$1,836 |
| 20 ft (170 sq ft) | $208–$840 | 5 sheets: $675–$730 | $2,540–$3,040 | $850–$2,040 |
| 22 ft (187 sq ft) | $229–$924 | 6 sheets: $810–$876 | $2,794–$3,344 | $935–$2,244 |
| 24 ft (204 sq ft) | $249–$1,008 | 6 sheets: $810–$876 | $3,048–$3,648 | $1,020–$2,448 |
| 26 ft (221 sq ft) | $270–$1,092 | 7 sheets: $945–$1,022 | $3,302–$3,952 | $1,105–$2,652 |
What's in a pontoon boat flooring kit
At PontoonStuff, carpet kits start at $376.99, vinyl kits run $664.99–$873.99 and complete deck kits $960.99–$1,457.99. Everything Pontoon's 24-ft re-deck kit ($1,653.74) is a good shopping list: six sheets of 3/4-inch 7-ply marine plywood, 100 stainless deck screws, 32 rail bolts with lock nuts, 32 rail risers, 3 gallons of roll-on glue and 24 ft of 80-mil vinyl.
Shop pricing varies most. The one shop we found that publishes rates charges $127 per foot of boat, $400 per plywood sheet and $5 per replacement fastener, so a 22-ft boat with six new sheets runs about $5,200. One cost guide puts professional marine flooring labor anywhere from $3 to $15 per sq ft.
Every pontoon on your lot has a deck. Coat them yourself.
Boat and UTV dealers add sprayed decks and hull protection as a service line. We supply the polyurea, the equipment and on-site or virtual training that ends in certification. Turnkey systems start at $25,000, low-pressure 1:1 equipment from about $20,000, with third-party financing. No franchise fee, no dealership fee, no royalty.
How to replace pontoon flooring
These steps follow Pontoon Specialists' re-decking and vinyl guides, with PMI's notes on seams and adhesive.
Photograph, then strip
Take "a lot of pictures," then remove furniture, fence and the old floor. Replace under-deck wiring and tighten under-deck hardware while it's open.
Lay and fasten the plywood
Set sheets "square and properly centered on the cross-members," tape the seams with butyl and fasten: at least six screws per cross-member at joints and five on center cross-members.
Glue at 60°F or warmer
Roll white marine glue on with a 3/8-inch or deeper nap and wait for the water to "flash out." Lay carpet when the glue is tacky but not yet clear.
Roll, staple, trim
Roll the floor from the center out with a floor roller (a 12–16 inch board works), staple the edges where the aluminum edge cap will cover them and trim flush.
Reinstall and keep it dry
Bolt the fence back on with rail risers, reinstall the furniture and keep the deck dry for at least 24 hours for carpet and "at least a few days" for vinyl.

If you're having it sprayed instead
The first two steps are the same. Then the applicator sands, cleans and primes the plywood, reinforces the joints, sprays the polyurea with grit broadcast into the wet film and adds an aliphatic top layer if the deck sees sun. Failures usually trace to prep: a coating that sets in seconds locks in contamination and moisture, and the surface should be at least 5°F above the dew point. As our marine page puts it, prep is "the single largest predictor of how long a marine coating lasts."
Care and cleaning by material
Hose weekly, scrub gently
Woven Flexa says vacuum or hose weekly, wash with mild soap and a soft brush, and use 1 cup of bleach and 1/4 cup of mild soap per gallon of water for tough stains.
Dry it out
Carpet needs regular cleaning and ventilation to prevent mildew (Great Lakes Skipper). Open the cover on dry days.
Soap, water, stiff brush
Soap, water and a stiff brush, with Dek Magic for stubborn stains; clean spills promptly.
Rinse and inspect
Hose off grit and check high-wear spots each season. An aliphatic top layer keeps the color.
Keep water off the plywood
Check seams, edge cap and bolts; retighten loose fasteners and seal any new hole.
Rinse after every trip
Rinse any floor with fresh water. Deck coatings aren't antifouling paint: polyurea "does not contain the biocides."
Get new boat deck guides and price updates by email: join the ArmorThane newsletter and tick "Marine."
Sprayed pontoon decks from certified applicators
ArmorThane has made polyurea and polyurethane coatings since 1989, and our certified applicators work in more than 50 countries. They spray seamless, textured decks on boats, docks and marinas, with color-stable aliphatic options for decks in the sun. See the marine coatings gallery and our automotive and marine coatings.
If new vinyl suits your pontoon, buy vinyl. If you want a seamless deck with the grip you choose, use the applicator finder to get a local quote. Still deciding? The ArmorThane newsletter sends new boat deck guides as we publish them.

Pontoon boat flooring FAQ
What is the best flooring for a pontoon boat?
For most owners it's marine vinyl or woven vinyl glued to 3/4-inch treated plywood. Vinyl cleans easily and protects the plywood from moisture; woven adds a softer, textured feel. Carpet is cheaper but holds water and can mildew. EVA foam is softest, and sprayed polyurea is the seamless choice for fishing and rental boats.
How much does it cost to replace a pontoon boat floor?
Doing it yourself, vinyl or woven rolls cost about $10 to $42 per running foot in September 2026, or $230 to $925 for a 22-ft deck plus adhesive. Six new plywood sheets add about $810 to $876. One Michigan shop charges $127 per foot of boat to remove the old floor and install vinyl, plus $400 per plywood sheet.
Is vinyl or carpet better on a pontoon boat?
Vinyl, for most boats. Harris, which builds pontoons, uses foam-backed vinyl and notes that carpet is prone to mildew and hard to clean. Marine Fabricator says wet carpet holds moisture like a sponge. Carpet still makes sense on a covered or indoor-stored boat where comfort and price matter most.
Does vinyl pontoon flooring get hot in the sun?
It can. Harris says high temperatures can make both solid and woven vinyl warm, and sellers disagree about which is cooler without publishing test conditions. Color matters more: the U.S. Department of Energy says reflective roofs can stay more than 50 degrees F cooler in summer sun, so choose a light color for an uncovered boat.
What is woven vinyl pontoon flooring?
It's a mat of PVC-coated yarns over a cushion backing, sold in rolls about 8 ft 6 in wide. It's softer and more textured than solid vinyl, doesn't soak up water and can be power washed. Prices ran about $17.56 to $42 per running foot in September 2026.
What plywood is used on pontoon boat decks?
Most use 3/4-inch CCA-treated marine plywood, usually Douglas fir, in 4 ft by 8 ft or 4 ft by 8 ft 6 in sheets laid across the deck. Sellers priced it at $125 to $145.99 a sheet in September 2026. One seller warns that copper sulfate alternatives delaminate within years.
How do I know if my pontoon deck is rotten?
Walk the whole deck and press near the seams, fence posts and furniture bolts. Soft or spongy spots, flex between cross-members and bolts that won't stay tight usually mean wet or rotten plywood. Replace those sheets before installing any new flooring, because every floor needs a sound, dry deck.
Can you spray bedliner or polyurea on a pontoon deck?
Yes. A trained applicator can spray polyurea over sound plywood or aluminum for a seamless, textured deck. The plywood must be dry, tight and primed, and treated plywood needs the coating maker's primer and an adhesion test. Aromatic polyurea darkens in sun, so ask for an aliphatic top layer on uncovered boats.
What is a non skid deck coating?
It's a textured coating that adds grip to a deck. Options range from roll-on acrylic non-skid, which doesn't seal the surface, to one-part polyurethane liners at about 60 sq ft per gallon, to professionally sprayed polyurea that forms a seamless waterproof membrane with built-in texture.
How much does a boat floor coating cost?
A DIY roll-on such as Durabak 18 costs $159.95 a gallon and covers about 60 sq ft in two coats, about $2.67 per sq ft. Professionally sprayed polyurea floors run about $5 to $12 per sq ft installed on published floor benchmarks. No pontoon-specific price is published, so get a quote after an inspection.
How long does pontoon flooring last?
There's little neutral data. One vinyl maker offers a prorated 2-year warranty and a woven brand offers 10 years. SeaDek fabricators quote 5 to 7 years for EVA foam in harsh use. Plywood warranties range from 6 years to limited lifetime. Keeping water off the plywood matters more than the brand.
How do you clean pontoon boat flooring?
Hose vinyl and woven vinyl weekly and scrub with mild soap and a soft brush; one maker suggests 1 cup of bleach and a quarter cup of mild soap per gallon of water for tough stains. Carpet needs regular cleaning and time to dry. EVA foam cleans with soap, water and a stiff brush.
Written from pontoon builders' and flooring makers' published guidance, installation guides, warranty documents, retail and shop prices read September 27, 2026 and decades of making marine coatings. Reviewed September 27, 2026.
Methodology and sources
Prices are retail or published shop prices on the date shown; figures marked as ours are arithmetic on them. Spray costs are floor-coating benchmarks. Heat claims for woven vinyl and EVA foam come from sellers. The selector's weighting is our judgment.
- Pontoon Specialists, ReDeck Kits, Plywood, installation guides and MariDeck warranty: pontoonspecialists.com
- PMI Marine, Pontoon Decking and Flooring Options: pmimarine.com
- PontoonStuff / DeckMate, Pontoon Carpet and Vinyl Flooring; 3/4" Marine Grade Plywood: pontoonstuff.com
- Everything Pontoon, 24 Foot Pontoon Re-Deck Kit: everythingpontoon.com
- Great Lakes Skipper, Pontoon Boat Vinyl Flooring and flooring guide (Feb. 2024): greatlakesskipper.com
- Marine Vinyl Fabric, Woven Flexa Marine Flooring: marinevinylfabric.com
- Oakland Shrink Wrap and Marine Services, Replace Flooring – Pontoon: oaklandshrinkwrap.com
- Decked Out Factory, Marine Flooring Cost Per Square Foot Guide (Nov. 2024): deckedoutfactory.com
- SeaDek, Two Color Full Sheet – Brushed; RecPro SeaDek sheet listing: seadek.com
- USATuff, SeaDek FAQ: usatuff.com
- Unmatched Marine, How Much Does SeaDek Cost? (Sep. 2026): unmatchedmarine.com
- Harris Pontoon Boats, Flooring Options: Making the Ideal Choice (Feb. 2019): harrisboats.com
- Marine Fabricator, The Woven Revolution (May 2014): marinefabricatormag.com
- Better Life Technology (G-Floor), Is Vinyl Marine Flooring Hot to Walk on in Bare Feet? (Sep. 2019): bltllc.com
- Veranda Marine, Aluminum Pontoon Boats: verandamarine.com
- U.S. Department of Energy, Energy Saver: Cool Roofs: energy.gov
- eCFR, 23 CFR 658.15 Width: ecfr.gov
- HomeGuide, Polyurea Garage Floor Coating Cost (Sep. 2025): homeguide.com
- MIL-SPEC LINER, MS0325 Pure Polyurea TDS (2024): milspecliner.com (PDF)
- Spray-Lining and Coatings Network, Simple Math to Calculate Bedliner Coverage: spray-lining.net
- Key Resin, Technical Bulletin #1-D Surface Preparation – Wood (2021): keyresin.com (PDF)
- Duraamen, How to Prepare Plywood to Apply Resinous Flooring (Mar. 2026): duraamen.com
- Croc Coatings, How To Prevent Polyurea Coating Failures (Nov. 2025): croccoatings.com
- Durabak, Marine Liner and Full FAQ: durabakcompany.com
- Boating, How to Apply Durabak Nonskid (Sep. 2017): boatingmag.com
- PYI Inc., KiwiGrip FAQ: pyiinc.com
- ArmorThane, Marine Coatings, product pages, Aromatic Polyurea, Two-Part Pour Foam and Garage Floor Coating Cost: armorthane.com
Boat deck guides and prices in your inbox.
Pontoon and boat deck guides, flooring price updates and marine coating projects from the people who make ArmorThane polyurea.
- New boat deck and flooring guides
- Price updates on materials and pro installs
- Real marine coating projects
Commercial & Industrial Floor Coatings
Flip through the whole brochure right here, or open it full screen on Issuu to share it.
Pick the floor for how you boat. Then build it on a sound deck.
Vinyl, woven vinyl, carpet and foam all have a place on a pontoon. When you want a seamless, textured deck, ArmorThane-certified applicators spray polyurea systems made in Springfield, Missouri. Boat and marine businesses: we train applicators with no franchise fee.
Soft spots, soggy carpet or peeling vinyl? Get a quote from a certified applicator.
Tell us your boat's length and what's on the deck now. We'll connect you with an ArmorThane-certified applicator who can check the plywood and quote a seamless, textured polyurea deck.
- Seamless coating, no joints for water to track behind
- Traction tuned from light texture to aggressive
- Color-stable aliphatic options for sun-exposed decks
- Marinas and boat dealers: ask about becoming an applicator
More to read on floors and decks
Short reads from ArmorThane on Issuu. Tap one to open it right here.
More in Automotive & marine
Automotive & marineBedliner Near Me | Find Certified Spray-On Bedliner Installers Near You
Automotive & marineBedliner Removal
Automotive & marineBest Spray-In Bedliner
Automotive & marineBoat Deck Paint
Automotive & marineCar Undercoating
Automotive & marineCar Wash Floor Coating
Automotive & marineCommercial Truck Coatings
Automotive & marineDock Coating








