Skip to content
Spray Rigs For Sale

Spray Rigs for Sale: Foam & Polyurea Rigs Built to Work

What comes on a turnkey trailer rig, how 20, 24 and 26 ft builds compare, what to check on a used rig and how to get a written quote.

Inside an ArmorThane polyurea spray trailer

Start a protective coatings business

Spray protective coatings for a living.

ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.

ArmorThane Mobile Coatings Unit trailer hitched to a pickup outside the plant Proportioner, A and B material drums and transfer pumps inside the spray rig Applicator in a protective suit holding a plural-component spray gun in a spray booth Proportioner control panel with heater, pressure balance and cycle counter controls

What comes with itProportioners, guns and complete spray rigs. We build them.

$0
franchise fees or royalties
35+
years in business
50+
countries with applicators
24/7
technical support
20 ft
Bumper-pull rig we build most often
Also a 24 ft bumper-pull and 26 ft gooseneck
3,500 psi
PMC PHX-40 on the 20 and 24 ft builds
Hydraulic, 2.8 gal/min
400 ft
Heated hose on the 26 ft gooseneck
100 ft on the 20 and 24 ft builds
24/7
Tech line for ArmorThane applicators
Included with equipment packages

Anyone searching for a spray rig for sale is really shopping for three things at once: a proportioner that meters material the way the data sheet says it should, a trailer that carries power, air and drums without fighting the crew, and someone who picks up the phone when the pressures drift apart at six in the morning on a job site. This page covers all three.

Quick answer

A spray rig is usually an enclosed trailer built around a heated plural-component proportioner, with heated hose, spray guns, a generator, an air compressor and dryer, transfer pumps and heated drum storage. The rig ArmorThane builds most often is a 20 ft bumper-pull with a PMC PHX-40 proportioner, a 45 kW diesel generator, a 23 CFM compressor, 100 ft of heated hose and four heated 55-gallon drums. We also build a 24 ft bumper-pull and a 26 ft gooseneck, and every build can be customized. Size yours with the matcher below, then ask for a written quote. Every one of our spray rigs for sale is built, tested and supported by ArmorThane.

The build

What comes on a turnkey spray rig

"Turnkey" gets stretched in classified ads. Sometimes it means a machine strapped into a cargo trailer. On a rig that is ready to work, every part is sized to the others: the generator can carry the proportioner's heaters and the hose heat at the same time, the compressor keeps up with the gun and the pumps, and the drums sit where the transfer pumps can reach them without a crew member wrestling a barrel in the dark.

Here is what a working rig carries, what our 20 ft build carries, and what to check on any rig you are considering.

ComponentWhat it doesOn our 20 ft buildWhat to check on any rig
ProportionerMeters, heats and pressurizes the A and B sides so they meet at the gun in the right ratioPMC PHX-40: hydraulic, 3,500 psi, 2.8 gal/min, 15, 18 or 21 kW dual heaters, supports up to 410 ft of heated hosePressure balance under load, heater capacity, parts and service support for that brand
GeneratorPowers the proportioner, primary heaters, hose heat, pumps and lights45 kW diesel, 3-phaseRated output against the full electrical load with every heater on; hours on the meter
Air compressor and dryerSupplies the gun, transfer pumps and cleanup air, and keeps it dry23 CFM compressor; desiccant air dryer with two-stage pre-filtrationEnough volume for guns and pumps together, plus clean, dry air; moisture reacts with the A side
Heated hoseHolds material at spray temperature all the way to the gun100 ft (2 × 50 ft) on a wall rack, with a curb-side hose hatchLength you actually need to reach the work, heat sensor function, condition of the scuff jacket
Drums and transfer pumpsStore material and feed it to the proportionerFour 55-gallon drums with base heaters and 2:1 transfer pumpsHow many drums ride along, and whether they stay warm enough to pump in cold weather
Spray gunMixes A and B at the tip and shapes the patternOne PMC Xtreme air-purge gunMixing chamber sizes for foam and for polyurea, rebuild kits and spare parts on hand
LayoutKeeps the hot, loud equipment away from the working areaTwo rooms: equipment room forward, spray room aftGenerator exhaust routing, how drums are secured, and room to move during setup
20 ft build details from ArmorThane's 3D rig pages. Every build can be customized, and your written quote lists exactly what is on yours.
ArmorThane mobile coatings unit spray rig during the build
An ArmorThane Mobile Coatings Unit during the build. Layout decisions made here decide how fast a crew can set up and tear down on every job.
Why the trailer mattersTwo rigs with the same proportioner can work very differently. Where the generator exhaust goes, how the drums are secured, where the hose rack sits and how much room is left to move decide whether setup takes ten minutes or forty. Walk through a rig before you buy one, or take a 3D tour of our 20 ft rig.
Sizes

20 ft, 24 ft or 26 ft gooseneck

Most contractors start with the 20 ft bumper-pull, the rig we build most often. The 24 ft is also a bumper-pull: the same core equipment with four more feet of spray room, shelving for parts and extra guns. The 26 ft gooseneck is a different class of rig, with a bigger proportioner, 400 ft of heated hose and four guns. Bigger is not automatically better, though; a rig that is more than the work needs costs more to tow, park and insure.

Built most often

20 ft bumper-pull

A two-room rig, equipment forward and spray room aft, on tandem torsion axles with electric brakes.

  • Bedliners, RV roofs, residential insulation
  • One PHX-40 system, changed over between materials
  • No gooseneck hitch needed
Take the 3D tour →
More room

24 ft bumper-pull

Everything in the 20 ft, plus four more feet of spray room, steel storage shelving with parts bins and two Graco Fusion AP guns.

  • Crews that spray most days
  • Same PHX-40, generator, compressor and hose
  • Still bumper-pull, no gooseneck hitch
Take the 3D tour →
Largest build

26 ft gooseneck

A PMC Premier X proportioner with touchscreen data reports and web remote access, 400 ft of heated hose and four Graco Fusion AP guns.

  • Large roofs, commercial insulation, industrial work
  • Long reaches from wherever the trailer parks
  • The only build that needs a gooseneck hitch
Take the 3D tour →
Spec20 ft bumper-pull24 ft bumper-pull26 ft gooseneck
HitchBumper-pull; tandem torsion axles, electric brakesBumper-pullGooseneck
ProportionerPMC PHX-40, hydraulic, 3,500 psi, 2.8 gal/minPMC PHX-40PMC Premier X, 18 kW; touchscreen with daily data reports and web remote access
Generator45 kW diesel, 3-phase45 kW diesel, 3-phase40 kW Perkins diesel, Tier 4 Final, 3-phase
Air compressor23 CFM23 CFMSchulz SRP 3008, 7.5 HP rotary screw, 25–27 CFM at 125 psi
Air dryerDesiccant, two-stage pre-filtrationDesiccant, two-stage pre-filtrationTsunami Pure-10 regenerative desiccant, 40 CFM
Heated hose100 ft (2 × 50 ft)100 ft (2 × 50 ft)400 ft (8 × 50 ft)
Spray gunsOne PMC Xtreme air-purgePMC Xtreme plus two Graco Fusion APFour Graco Fusion AP
DrumsFour 55-gal with base heaters, 2:1 transfer pumpsSame as the 20 ftSpecified on your quote
Extra roomTwo rooms: equipment forward, spray aftFour more feet of spray room, steel shelving with parts binsThe largest build we offer
From ArmorThane's 3D rig pages. Every build can be customized; your written quote lists exactly what is on yours.
Weigh the truck question firstA loaded spray rig carries a generator, a compressor, a proportioner and full drums. Get the loaded weight on your quote and match it to your truck's towing and hitch ratings before you choose a size. The 20 ft and 24 ft are bumper-pull trailers; only the 26 ft needs a gooseneck hitch.
Rig matcher

Spray rigs for sale: which fits your work?

Answer five questions. The matcher weighs material, workload, crew size and tow vehicle the way our equipment team does on a first call, then suggests a size you can tour in 3D and send to us for a written quote.

Rig sizing

Spray rig matcher

A rule-of-thumb guide, not a quote. Heavier workloads, bigger crews, combined foam and polyurea work and industrial jobs push toward the 24 ft bumper-pull or the 26 ft gooseneck. The 20 ft and 24 ft are bumper-pull; only the 26 ft needs a gooseneck hitch. Final sizing, options and loaded weight come on the written quote; match that weight to your truck's towing and hitch ratings.

What will you spray?
20 ft
Suggested rig
Both
Materials on board
Bumper-pull
Hitch it needs

    Want to see the parts in person? The polyurea spray rigs page shows the full lineup, and the polyurea equipment guide explains proportioners, hoses and guns in more depth.

    One rig, two trades

    Spraying foam and polyurea from the same rig

    A well-specified rig can spray both spray foam insulation and polyurea coatings, and that is one of the strongest arguments for buying a proper rig instead of a single-purpose machine. Foam and coatings sell to different customers, so a contractor who can do both has more doors to knock on and fewer empty days on the calendar.

    Spray foam

    Insulation and roofing work

    • Walls, attics and crawl spaces
    • Pole barns and metal buildings
    • Spray foam roofing

    Material: ArmorFoam open-cell and closed-cell.

    Polyurea

    Coatings and linings

    • Truck bedliners and trailers
    • RV and commercial roofs
    • Containment, waterproofing and industrial equipment

    Material: ArmorLine high-pressure polyureas.

    Switching between the two is routine work, not a rebuild, but it has to be done right. Foam and polyurea run at different temperatures and pressures, often through a different mixing chamber in the gun, and the lines have to be flushed so one material never contaminates the next. On our 20 ft and 24 ft builds that means one PHX-40 system changed over between jobs. The 24 ft carries two Graco Fusion AP guns in addition to the PMC Xtreme, and the 26 ft gooseneck carries four. Every build can be customized, so tell our equipment team how your work splits between foam and coatings.

    Changeover disciplineFollow the data sheet for each material's processing temperature and pressure, flush before switching, and log it. Most "bad batch" calls that turn out not to be bad batches start with a rushed changeover.
    New or used

    New vs used spray rigs: what the market looks like

    Used spray foam rigs for sale show up constantly, and some are good buys. The problem is that a rig's history lives in the parts you cannot see in photos: heater elements, pump seals, hose heat circuits and how carefully the last owner flushed the system. The ranges below are market data we collected for our spray foam machine guide. They are not ArmorThane prices, and we quote every build in writing.

    What you buyMarket range (2026)Where the number comes fromWatch for
    Proportioner only$26,000–$53,0002026 dealer listings for heated plural-component machinesYou still need a trailer, generator, compressor, hose, gun and pumps
    New trailer rig package$38,000–$140,000Published 2026 packages from several buildersWhat is actually included: hose length, generator size, training, support
    Used trailer rig$60,000–$99,000 listedListings for Graco E-20 to H-40 rigs, September 2026Hours, rebuild history, who will service it, and no training included
    First chemical, respirators and training$12,000–$16,000Startup budget from our spray foam machine guideSupplied-air respirators and fit testing are not optional
    Market ranges from ArmorThane's spray foam machine guide; not ArmorThane pricing. Tap a column heading to sort.

    Used rig checklist

    • Hours on the generator and proportioner. Ask for service records, not just a number on a meter.
    • A live spray test. Watch both pressures stay together under load and the hose hold temperature for the full length.
    • Heater and hose heat circuits. A dead zone in the hose is a cold spot in the material and a bad mix at the gun.
    • Pump seals and filters. Crystallized A-side material in the pumps is a sign the rig sat without proper care.
    • What it last sprayed. A rig that ran foam needs a clean changeover before it sprays polyurea, and the reverse.
    • Title, VIN and registration for the trailer. The trailer is a vehicle; buy it like one.
    • Who will service it. If the original builder will not support it, budget for a technician who will.
    The hidden line itemA used rig almost never comes with training, certification or a tech line. If you are new to plural-component spraying, price those in before comparing a used listing with a new rig that includes them.
    After the sale

    What comes with an ArmorThane rig besides the rig

    We manufacture the coatings and the equipment, so the people who train your crew are the same people who formulate the material you will be spraying. That matters most in the first few months, when every odd pattern and every pressure alarm feels like an emergency.

    Included

    Hands-on training

    Equipment packages include hands-on training on the machine and the materials, so the first paying job is not the first time anyone pulls the trigger.

    Included

    Certification

    Certified applicators can be listed for customer requests that come through armorthane.com and routed by location.

    Included

    24/7 tech line

    Applicators call our technicians day or night, including the weekend calls that always seem to happen mid-job.

    The terms

    No franchise fee, no royalties

    You own your business and your customers. There is no franchise fee and no royalty on the work you sell.

    Need to finance it? Third-party equipment financing is available for our packages; ArmorThane does not finance in-house, but we will give you the written equipment quote a lender asks for. Not ready for a full trailer yet? Our published low-pressure starter package is $25,000 and a high-pressure system runs about $50,000. Those are equipment packages, not trailer rigs, and the become an applicator page explains what each one includes.

    When you compare spray rigs for sale, look past the price tag. Ask what proportioner, generator and compressor are on board, how much heated hose is included, whether training is part of the package and who you will call when something goes wrong on a job. A cheaper rig with no support can cost far more in lost days than it saves up front. See our 20 ft spray rig, 24 ft spray rig and 26 ft gooseneck spray rig to compare builds.

    Next step

    How to get a written rig quote

    1. Tell us the work

      What you plan to spray, who you plan to sell it to and roughly how many jobs a week. A body shop adding bedliners and a roofer adding foam need very different rigs.

    2. Size the rig

      Start with the matcher above, then talk it through with our equipment team. We will ask about your truck, your crew and where you will park the trailer.

    3. Get it in writing

      Make, model, options and what is included, on one quote. That document is what an equipment lender will ask for, and it is what you should compare against any other rig.

    4. Line up financing if you need it

      Take the quote to your bank or a third-party equipment lender. Compare total cost across terms, not just the monthly payment.

    5. Train before the first job

      Schedule training with the crew who will actually spray, and keep the tech line number in every phone on the rig.

    Rig quotes

    Size it right. Get it in writing.

    Tell us what you plan to spray and where. Our equipment team will recommend a rig, spell out what is on it and send a written quote you can take to a lender.

    Questions first? Call (417) 831-5090

    FAQ

    Spray rig questions

    How much does a spray rig cost?

    It depends on the proportioner, generator, hose length and layout. In 2026 market data, a proportioner alone listed for about $26,000 to $53,000 and published new trailer rig packages ran about $38,000 to $140,000. ArmorThane quotes each rig in writing based on the work you plan to do.

    Can one rig spray both spray foam and polyurea?

    Yes. A well-specified rig sprays both. The materials run at different temperatures and pressures, so the system is flushed and changed over between them, and the gun may use a different mixing chamber. Every ArmorThane build can be customized for your mix of work.

    What size generator does a spray rig need?

    Enough to run the proportioner's heaters, the hose heat, the pumps and the compressor at the same time. ArmorThane's 20 ft and 24 ft rigs use a 45 kW diesel generator with a PMC PHX-40, and the 26 ft gooseneck uses a 40 kW Perkins Tier 4 Final diesel with a PMC Premier X. Match the generator to the full electrical load, not just the machine.

    Should I buy a used spray foam rig?

    A used rig can be a good buy if you can see it spray, review its service records and find someone to support it. Used rigs rarely include training, certification or a tech line, so add those costs before comparing a used listing with a new rig.

    Do I need a gooseneck truck for a spray rig?

    Only for the 26 ft build. ArmorThane's 20 ft and 24 ft rigs are bumper-pull trailers, and the 26 ft is the only gooseneck. Whatever the size, get the loaded weight on your quote and match it to your truck's towing and hitch ratings before you decide.

    Does ArmorThane offer financing on spray rigs?

    Third-party equipment financing is available for ArmorThane packages. ArmorThane does not finance in-house, but it provides the written equipment quote that lenders ask for and can point you to lenders who finance coating equipment.

    About the numbersMarket ranges on this page come from published listings and packages collected for our spray foam machine guide. They are not ArmorThane prices, which are provided only on a written quote.
    AT
    Written by the ArmorThane equipment team. We have manufactured polyurea, polyurethane and polyaspartic coatings and plural-component spray equipment in Springfield, Missouri since 1989, and we build the trailer rigs our applicators spray from.

    Sources

    1. ArmorThane, 20 ft bumper-pull spray rig (3D tour and build details). armorthane.com/products/polyurea-spray-rigs/20-ft-spray-rig/
    2. ArmorThane, 24 ft bumper-pull spray rig (3D tour and build details). armorthane.com/products/polyurea-spray-rigs/24-ft-spray-rig/
    3. ArmorThane, 26 ft gooseneck spray rig (3D tour and build details). armorthane.com/products/polyurea-spray-rigs/26-ft-gooseneck-spray-rig/
    4. ArmorThane, Spray foam machine guide (2026 market ranges for machines and rigs). armorthane.com/spray-foam-machine/
    5. OSHA, Respiratory Protection standard, 29 CFR 1910.134. osha.gov/laws-regs/regulations/standardnumber/1910/1910.134

    A rig sized to the work, backed after the sale.

    ArmorThane builds trailer rigs around the proportioner, trains your crew and stays on the phone with a 24/7 tech line. No franchise fee and no royalties.

    United States 417-831-5090 · Canada 780-444-6200
    Cover of the ArmorThane brochure: Polyurea & Spray Foam Equipment 2025
    Brochure

    Polyurea & Spray Foam Equipment 2025

    Flip through the whole brochure right here, or open it full screen on Issuu to share it.

    Become an applicator

    Start your coatings business with ArmorThane.

    Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.

    • Equipment package matched to your applications
    • Hands-on training and applicator certification
    • Technical support once you are spraying
    Step 1 of 3

    We want to help you find the best ArmorThane applicator for your protective coating project. Please either fill out the request form below or call us toll free at 417-831-5090, any time Monday-Friday, 8:00 a.m. to 5:00 p.m. Central Standard Time.

    Shopping for a rig? Get it in writing.

    Tell us what you plan to spray and where. Our equipment team will size the rig to the work and send a written quote you can take to a lender.

    • What you plan to spray
    • Shop, mobile or both
    • Your truck and your city
    • Rough timing and budget
    Become an applicator

    Start your coatings business

    Choose “becoming an Applicator / Dealer” and add your details. Our team will call you to talk through markets, equipment and budget.

    1Choice
    2Contact Information
    3Location

    Rather talk now? (417) 831-5090 · About the opportunity