Asphalt Roof Coating: Types, Coverage, Cost & When Not to Use It
Fibered asphalt, emulsions, resaturants and aluminum: which asphalt roof coating goes on which low-slope roof, how much it takes, what it costs per year, and why it does not belong on shingles.

Start a roof coating business
Spray roofs for a living.
ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.
- $0
- franchise fees or royalties
- 35+
- years in business
- 50+
- countries with applicators
- 24/7
- technical support
Asphalt roof coating is the black stuff in the 5-gallon pail: cut-back or emulsified asphalt, usually with fibers, brushed or squeegeed over built-up roofs, roll roofing, modified bitumen and old metal to keep the sun off the roof and buy a few more years. It is the cheapest coating on the shelf and it does a real job on the right roof. It also gets put on roofs where it can only make things worse, and it is often confused with the very different job of coating asphalt shingles. We manufacture spray polyurea and polyurethane systems, which sit at the other end of the price scale, so this guide is about when the cheap black coat is the right call and when it is not. It covers the types of asphalt roof coating and the ASTM standards behind them, which one goes on which roof, how much it takes, a cost-per-year comparison against white coatings, and how to put it down so it lasts.
An asphalt roof coating is a bitumen-based maintenance coat for low-slope asphalt roofs: built-up (BUR), modified bitumen, roll roofing and some metal. Fibered solvent asphalt coatings (ASTM D4479) go on at about 4 gallons per 100 sq ft; asphalt emulsions (ASTM D1227) at 3 to 4; resaturants that rejuvenate dried-out BUR at 7 to 8. Expect $1.00 to $2.50 per sq ft installed and 5 to 10 years of life. It needs a roof that drains, it absorbs heat because it is black, and it does not belong on asphalt shingles. For a reflective finish over asphalt, use an aluminum or white coating on top.
Types of asphalt roof coating and their standards
"Asphalt roof coating" covers four quite different products. The label will usually cite an ASTM standard, and that tells you more than the marketing copy.
Solvent-based asphalt coating
Asphalt cut back with solvent, fibered or not, brushed or sprayed. Type I uses asphalts that are self-healing, adhesive and ductile; Type II uses high-softening-point asphalt with lower ductility. Karnak's 71 fibered coating is a D4479 Type I, applied at 4 gallons per 100 sq ft from 40°F to 120°F, over smooth BUR, SBS modified bitumen, metal and roll roofing.
Asphalt emulsion coating
Asphalt dispersed in water with clay (Class 1) or chemical (Class 2) emulsifiers, with fibers or fillers (Types I and II) or without (Type III). Lower odor, water cleanup, and often used as a primer or base coat. D1227 covers built-up roofs and exposed surfaces with slopes of at least 4%, roughly 1/2 inch per foot.
Roof resaturant
A thin, oily asphalt that soaks into a dried-out BUR. Karnak describes its 198 as penetrating oils that rejuvenate old asphalt while leaving a surface layer that protects from UV and can bind new gravel. It goes on heavy, at 7 to 8 gallons per 100 sq ft.
Aluminum asphalt coating
Asphalt with aluminum flake for a silver, reflective face. It protects the asphalt from UV and reflects roughly 0.63 of sunlight when new. Full details are in our aluminum roof coating guide.
Asphalt roof coating picker
Choose the roof, its condition and what you want the coating to do. The picker returns the product type, the standard to look for on the label, the coverage rate, and anything that should stop you from coating at all.
Which asphalt roof coating does this roof need?
Rules from manufacturer data and standards cited on this page: D4479 fibered asphalt at 4 gal/100 sq ft, D1227 emulsions at 3–4 gal on slopes of at least 4% (about 1/2 in per foot), resaturant at 7–8 gal, D2824 aluminum at 1–1.5 gal, and no standing water 48 hours after rain.
Asphalt roof coatings compared
Click a heading to sort. Coverage and temperature limits come from representative manufacturer data; your product's data sheet governs.
| Coating | Standard | Coverage (gal/100 sq ft) | Min. application temp | Initial solar reflectance | Main job |
|---|---|---|---|---|---|
| Fibered solvent asphalt | ASTM D4479 | 4 | 40°F | Dark, 0.05–0.20 | UV protection for BUR, mod bit, roll roofing, metal |
| Asphalt emulsion | ASTM D1227 | 3–4 | Per data sheet | Dark, 0.05–0.20 | Low-odor coat or primer on sloped BUR |
| Roof resaturant | Manufacturer spec | 7–8 | 40°F | Dark, 0.05–0.20 | Rejuvenate dried BUR, rebind gravel |
| Fibered aluminum asphalt | ASTM D2824 Type III | 1–1.5 | 50°F | 0.63 | Reflective UV shield over asphalt |
| White acrylic over asphalt | ASTM D6083 | 3 (two coats) | 40–50°F | 0.85 | Cool roof finish, needs compatible primer |
Asphalt roof coating on shingles?
Search "asphalt roof coating" and you will find people asking whether to coat their shingle roof. Those are different jobs. Asphalt roof coatings are made for low-slope asphalt membranes. Asphalt shingles are a steep-slope, water-shedding system that needs to breathe and dry between the laps.
Brushing a black asphalt coating over shingles glues the tabs down, fills the gaps that let water drain, and adds nothing the granules were not already doing. Even purpose-made shingle coatings deserve caution: coating shingles can slow drying and trap moisture, and shingle manufacturers' warranties may be affected. If your shingles are curling, cupping or losing granules, the honest answer is usually repair or replacement. Our shingle roof coating page covers the narrow cases where a coating can make sense.
Asphalt roof coating cost per year calculator
Asphalt coatings win on price per square foot and lose on how often you have to redo them. This calculator spreads each option over the years you plan to own the building so you can compare like with like.
What will this roof cost to keep coated?
Applications = horizon / service life, rounded up. Low case uses the low price and long life, high case the high price and short life. Installed price and life ranges: asphalt $1.00–$2.50 and 5–10 yrs (HomeGuide, The Roofing Brief); acrylic $0.50–$3.00 and 7–20 yrs, silicone $1.50–$4.50 and 10–15 yrs (HomeGuide); polyurethane $1.50–$4.00 (HomeGuide) and 12–20 yrs (The Roofing Brief). Excludes repairs and inflation.
Talk to an applicator about a seamless membrane.
When a flat asphalt roof keeps blistering, splitting or ponding, certified ArmorThane applicators can spray polyurea or foam roofing over a repaired, dry substrate. If a fresh asphalt or aluminum coat is all you need, they will say so.
Contractors: become an applicator →
How to apply asphalt roof coating so it lasts
Find the water first
Cold-process coatings belong only on roofs with positive drainage; Karnak's rule is no standing water 48 hours after rain stops. Probe soft spots and blisters. Coating over wet insulation seals the water in and the deck keeps rotting.
Repair splits, blisters and flashings
Cut out blisters, dry and patch them, and reinforce splits and flashing joints with roof cement and polyester fabric. Let the repairs set before coating over them.
Clean the surface
Sweep off loose gravel, dirt and debris. On gravel roofs, decide whether you are resaturating and regraveling or removing loose gravel for a coating; you cannot do both.
Check weather and temperature
Solvent asphalt coatings typically go on from 40°F to 120°F. Below 40°F, Karnak requires the surface to be free of moisture and ice. Emulsions must not get rained on before they set and should not freeze.
Apply at the full rate
Brush or squeegee fibered coatings at about 4 gallons per 100 sq ft, working them into the surface. A thin coat looks fine on day one and cracks the first summer.
Add a reflective top if you want it cool
Black asphalt runs hot; DOE notes conventional roofs can top 150°F. Once the base has cured, an aluminum coat or a compatible white elastomeric over a bleed-resistant primer drops surface temperature substantially. See our acrylic roof coating guide.
Asphalt roof coating questions
What is asphalt roof coating used for?
It is a maintenance coat for low-slope asphalt roofs: built-up roofing, modified bitumen, roll roofing and some metal roofs. It shields the asphalt from UV and weathering, fills minor surface cracks and extends the life of a roof that is still basically sound and dry.
How long does asphalt roof coating last?
The Roofing Brief puts asphalt emulsion coatings at 5 to 10 years with 3 to 7 year warranty terms. Real life depends on thickness, sun exposure and drainage. Plan on inspecting yearly and recoating when the surface starts to craze or chalk.
How much does asphalt roof coating cost?
HomeGuide and The Roofing Brief both put bitumen or asphalt emulsion coatings at about $1.00 to $2.50 per sq ft installed. Repairs, cleaning and any reflective topcoat are extra. See our roof coating cost guide for every coating type side by side.
Can you put asphalt roof coating on shingles?
We advise against it. Black asphalt coatings are made for low-slope membranes; on shingles they glue the tabs, interfere with drainage and drying, and may affect the shingle warranty. Spot repairs with roof cement are fine.
What is the difference between fibered and non-fibered asphalt coating?
Fibered coatings contain reinforcing fibers that build a thicker film and bridge small cracks, and they are applied heavier, around 4 gallons per 100 sq ft. Non-fibered coatings are thinner, spray more easily and are often used as primers or on smoother surfaces.
What is a roof resaturant?
A resaturant is an oily asphalt that soaks into a dried-out built-up roof to rejuvenate it, leaving a surface layer that blocks UV and can bind new gravel. It goes on heavy, about 7 to 8 gallons per 100 sq ft.
Can you put asphalt coating on a metal roof?
Fibered asphalt coatings are listed for metal roofs, and they protect old barn steel cheaply. They are black and hot, though, and you cannot easily paint over them later. On metal you want to keep looking good, see our metal roof paint guide.
Can I put a white coating over an asphalt coating?
Yes, after the asphalt has fully cured and with a primer the white coating's maker approves for asphalt substrates, because asphalt oils can bleed through and stain or soften a white topcoat. Aluminum coatings are the traditional reflective top for asphalt.
Sources
- ASTM D4479, asphalt roof coatings, asbestos-free: store.astm.org/d4479_d4479m-07r18.html
- ASTM D1227, emulsified asphalt used as a protective coating for roofing: store.astm.org/d1227-13.html
- ASTM D2824, aluminum-pigmented asphalt roof coatings: store.astm.org/d2824_d2824m-18.html
- Karnak, 71 fibered asphalt roof coating: karnakcorp.com/product/71-fibered-asphalt-roof-coating
- Karnak, 198 asphalt roof resaturant: karnakcorp.com/product/198-asphalt-roof-resaturant
- Karnak, 97 fibered aluminum and 529 acrylic data: karnakcorp.com/product/97-fibered-aluminum-roof-coating
- HomeGuide, roof coating cost by type (2026): homeguide.com/costs/roof-coating-or-sealing-cost
- The Roofing Brief, roof coating types and cost (2026): theroofingbrief.com/roof-coating-types-and-cost
- The Roofing Brief, solar reflectance reference (2026): theroofingbrief.com/roofing-solar-reflectance-sri-reference-2026
- Wikipedia, roof coating (coating asphalt shingles): en.wikipedia.org/wiki/Roof_coating
- U.S. Department of Energy, cool roofs: energy.gov/energysaver/cool-roofs
- OSHA 29 CFR 1926.501, fall protection: osha.gov 1926.501
Flat roofs that stop needing recoats.
Building owners get a certified ArmorThane applicator who sprays seamless polyurea and foam roofing over repaired, dry roofs. Contractors can add spray roofing with no franchise fee and no royalties.
Protective Roof Coatings & Leak Repair
Flip through the whole brochure right here, or open it full screen on Issuu to share it.
Start your coatings business with ArmorThane.
Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.
- Equipment package matched to your applications
- Hands-on training and applicator certification
- Technical support once you are spraying
Flat roof blistering or leaking? Get a real fix.
Tell us the roof type and size, when it was last coated, how it drains and where it leaks. We will connect you with a certified applicator near you.
- Roof type and square footage
- Last coating and its age
- Leaks, blisters or ponding
- Building use and access
More to read on roofing
Short reads from ArmorThane on Issuu. Tap one to open it right here.

















