Metal Roof Paint: What Lasts, What Peels & When to Coat Instead
Which paint goes on galvanized, Galvalume, painted and rusted metal, the prep that decides whether it sticks, real 2026 costs, and where paint stops and a roof coating has to take over.

Start a roof coating business
Spray roofs for a living.
ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.
- $0
- franchise fees or royalties
- 35+
- years in business
- 50+
- countries with applicators
- 24/7
- technical support
Metal roof paint is one of the cheapest ways to make a faded, chalky or lightly rusted steel roof look new again, and one of the easiest jobs to get wrong. Most failed metal roof paint jobs we get called to look at did not fail because the paint was bad. They failed because alkyd paint went on galvanized steel, because nobody washed off the chalk, or because the owner expected a 3 mil paint film to stop a leaking fastener. We manufacture polyurea and polyurethane coatings, and we will tell you straight: for a lot of roofs, a good acrylic paint is the right answer and our products are overkill. This guide covers which paint goes on which metal, the prep that decides whether it sticks, what it costs, and where paint stops and a real coating system has to take over.
For most painted, galvanized or Galvalume roofs, use a 100% acrylic direct-to-metal (DTM) paint over an acrylic bonding primer, applied in two coats at 50°F or warmer. Never put alkyd or oil-based paint on galvanized steel; the zinc turns it to soap and it peels. Wash off all chalk and dirt, remove loose rust to at least hand-tool standard, and let new galvanized weather about six months first. Expect $1.20 to $2.70 per sq ft professionally applied and a repaint in roughly 10 to 15 years. If the roof leaks at seams or fasteners, paint will not fix it; that needs a 20+ mil roof coating or a spray-applied membrane.
Metal roof paint vs. roof coating
People use "paint" and "coating" interchangeably, but on a metal roof they are different products doing different jobs, and the difference is mostly thickness.
A direct-to-metal acrylic like Sherwin-Williams Pro Industrial DTM goes on at 6 to 10 wet mils and dries to 2.4 to 4 mils per coat. Two coats gets you somewhere around 5 to 8 mils. That is plenty to restore color, block UV and slow corrosion on sound metal. It is not enough to bridge a gap.
A roof coating is built to be a membrane. Karnak's 404 Corrosion Proof metal base coat, for example, goes on at 1.5 gallons per 100 sq ft for 20 to 24 dry mils, and that is just the base coat before the finish coat. Elastomeric acrylic, silicone and polyurethane roof coatings are designed to stretch with the panels as they expand and contract, and to be paired with fabric and sealant at seams and fasteners. A spray-applied polyurea membrane is thicker again.
- Paint is for appearance and corrosion protection on a roof that is still watertight: faded or chalking factory finish, surface rust on a barn roof, a color change.
- A coating system is for leaks and life extension: seams opening up, fasteners backing out, widespread rust, or a roof you want to keep in service another 10 to 20 years without tearing it off.
- A spray membrane is for the hard cases: badly corroded commercial roofs, hail-dented panels, roofs with lots of penetrations, or where you need a thick, seamless, fast-setting layer.
One more thing to know before you pick a color: dark roofs get hot. The U.S. Department of Energy notes conventional roofs can reach 150°F or more on a summer afternoon, while a reflective roof can stay more than 50°F cooler under the same sun. If the building is conditioned, a light color is worth considering. Our cool roof coating guide covers the numbers. Note that the ENERGY STAR roof products label ended on June 1, 2022, so check a product's Cool Roof Rating Council listing rather than an old ENERGY STAR claim.

The right metal roof paint for each metal
The metal under the paint decides the primer, and the primer decides whether the job lasts. Here is how we sort it out on a site visit.
Galvanized steel
Zinc-coated steel, often dull gray and spangled. Use an acrylic bonding primer and acrylic topcoat. Never alkyd or oil: Dunn-Edwards explains the zinc reacts with the fatty acids in alkyd resin and forms a soap-like layer that makes the paint delaminate. New galvanized needs to weather first; Sherwin-Williams calls for at least six months.
Galvalume / Zincalume
Aluminum-zinc coated steel with a brighter, smoother look. Bare Galvalume is very reflective (about 0.75 initial solar reflectance in LBNL data) but has low emittance, so it still runs warm. Treat it like galvanized: clean, acrylic bonding primer, acrylic topcoat. Check the panel maker's guidance before painting a roof still under warranty.
Painted steel (SMP or PVDF)
Most colored panels came with a baked-on silicone modified polyester (SMP) or PVDF (Kynar 500) finish. Chalky SMP takes paint well after a thorough wash. PVDF is hard to bond to by design; manufacturers sell specific primers for it, such as Karnak's 702 K-Prep, made for a surface that "traditionally has been difficult to bond against."
Rusted steel
Remove loose rust and flaking paint to at least SSPC-SP2 hand-tool cleaning, prime the same day you clean, and use a rust-inhibitive primer on the bare spots. Tight surface rust can be treated with a rust converter; heavy scale has to come off. If you can push a screwdriver through it, that panel needs replacing, not painting.
Aluminum
Aluminum does not rust, but its oxide layer makes adhesion tricky. Degrease, scuff, and use a primer labeled for aluminum. Most painted aluminum roofs only need a repaint for looks.
Copper and zinc
Copper and architectural zinc are chosen for the patina. Painting them is rarely worth it and often voids what made the roof valuable. If a copper roof leaks, it needs a sheet-metal repair.
Not sure what primer you need? Our metal primer guide goes deeper on bonding, rust-inhibitive and zinc-rich primers.
Metal roof paint selector
Tell the tool what metal you have and what shape it is in. It returns whether paint is the right call, the primer and topcoat type, the prep standard, and the mistakes to avoid for that combination.
What should go on this metal roof?
Logic follows the manufacturer guidance cited on this page: no alkyds on zinc (Dunn-Edwards), six months weathering for new galvanizing and SSPC-SP2 minimum on rust (Sherwin-Williams), and coating systems of 20+ dry mils where the roof leaks (Karnak 404).
Metal roof finishes compared
Click any column heading to sort. Film thickness is the total for a normal system, not one coat. Cost is installed, per square foot of roof.
| Finish | Typical dry film (mils) | Installed $/sq ft | Expected life | Stops leaks? | Best fit |
|---|---|---|---|---|---|
| DTM acrylic paint, 2 coats | about 5–8 | $1.20–$2.70 | Repaint every 10–15 yrs | No | Sound roof, color or rust touch-up |
| Alkyd / oil enamel | about 4–6 | Similar to acrylic | Peels on galvanized | No | Bare, primed carbon steel only |
| Elastomeric acrylic coating | 22–25 | $0.50–$3.00 | 7–20 yrs | Yes, with seam and fastener detailing | Sloped metal that drains |
| Silicone roof coating | about 22 per coat | $1.50–$4.50 | 10–15 yrs | Yes, with detailing | Low slope, slow drainage |
| Polyurethane roof coating | varies by system | $1.50–$4.00 | 12–20 yrs | Yes | Foot traffic, impact, hail areas |
| Factory PVDF (Kynar 500) | factory baked | New panels only | 35-yr chalk and fade warranty typical | Panel system dependent | New construction, re-roofing |
| Spray polyurea + aliphatic topcoat | thick, set per spec | Quote per job | Depends on topcoat upkeep | Yes, seamless | Corroded commercial and ag roofs |
Metal roof paint quantity and cost calculator
Most people under-buy paint for a metal roof because they measure the footprint of the building. The calculator corrects for roof pitch and for the extra surface in a ribbed or corrugated profile, then works out gallons of primer and paint.
How much metal roof paint do I need?
Surface = footprint x pitch factor (square root of 1 + (rise/12)²) x profile factor. Gallons = surface x coats / coverage, plus 10% waste. Profile factors are our geometry estimates for each panel shape. Pro cost uses $1.20–$2.70 per sq ft (HomeGuide, Angi 2026).
When paint is not enough, spray a membrane.
Certified ArmorThane applicators spray seamless polyurea and polyurethane systems over corroded, leaking metal roofs on barns, shops and commercial buildings, sealing fasteners and seams in the same pass.
Contractors: become an applicator →
How to paint a metal roof so it stays put
Paint adhesion is decided before the can is opened. This is the sequence we train applicators to follow on any metal roof, whether the finish is a DTM acrylic or a spray-applied membrane.
Set up fall protection and check for lead
OSHA requires fall protection for roofing work 6 feet or more above a lower level, on low-slope and steep roofs alike. On homes, child care facilities and preschools built before 1978, assume old paint may contain lead; the EPA's RRP rule requires certified firms when anyone is paid to disturb it.
Fix the roof before you paint it
Walk every panel. Replace stripped or backed-out fasteners with oversized screws and new washers, reseal laps and flashings, and replace any panel with rust-through. Paint hides these problems for one season, then they come back under a nice new color.
Wash off chalk, dirt and oil
Chalk is the number one adhesion killer on old painted panels. Scrub with a cleaner-degreaser and pressure wash; Karnak specifies at least 2,000 psi for its metal base coat. Rinse well, let it dry, and do the hand-wipe test again. If your palm comes back white, wash again.
Deal with rust properly
Remove loose rust and flaking paint to at least SSPC-SP2 hand-tool cleaning, or SP3 power-tool cleaning on heavier spots. Prime bare steel the same day so it cannot flash rust overnight.
Respect the zinc
On galvanized and Galvalume, use an acrylic bonding primer and skip anything alkyd or oil based. New galvanized should weather first: six months per Sherwin-Williams. Some coating makers allow less for their own primers (Karnak asks 30 days before its 404 base coat), so follow the data sheet of the product you are using.
Apply in the right weather, at the right thickness
Most acrylic DTMs need 50°F or warmer and a dry forecast. Apply two coats; at 77°F a typical DTM is recoatable in about an hour. Check thickness with a wet film gauge: wet mils x volume solids = dry mils, so a 40% solids paint at 8 wet mils leaves about 3.2 dry.
When metal roof paint is the wrong answer
We would rather you spend $3,000 on paint that is right for the roof than $15,000 on a coating you did not need. But there are clear cases where paint is a waste of money.
Faded or chalky, no leaks
Wash, prime where needed, two coats of acrylic DTM. This is the cheapest correct answer and it is what we would do on our own shop.
Leaks at seams and fasteners
Use an elastomeric roof coating system with fabric and sealant at every lap and screw head. Our metal roof coatings guide walks through the options.
Low slope with ponding
Paint and most acrylics do not like standing water. Look at silicone or a sprayed polyurea membrane, and fix the drainage if you can.
Widespread corrosion or rust-through
Replace perforated panels, then a thick seamless membrane is the long-term fix. See polyurea metal roof waterproofing.
Related roof coating guides
If your roof needs a coating rather than paint, compare acrylic roof coating for sloped metal that drains well, aluminum roof coating for low-cost reflectivity, and asphalt roof coating for old barn steel where looks do not matter. Our roof coating cost guide puts every option side by side on price.
Where ArmorThane products fit
Our applicators spray ArmorSeal 100 AL, a 1:1, 100% solids polyurea roofing liner with no solvents or VOCs. It is aluminized for reflectivity and bonds to steel, aluminum, copper and zinc. Because it is an aromatic formula, outdoor roofs get a UV TopCoat or ColorCoat within twelve hours. That is a membrane system, not a paint, and it only makes sense when the roof needs waterproofing. For the bigger picture across every roof type, start with our roof coating guide.
Metal roof paint questions
What is the best paint for a metal roof?
For most galvanized, Galvalume and previously painted steel roofs, a 100% acrylic direct-to-metal paint over an acrylic bonding primer. It stays flexible, holds color and is safe on zinc. Use a rust-inhibitive primer on bare or rusted steel, and a specialty primer on PVDF (Kynar) finishes.
Can I use oil-based paint on a galvanized metal roof?
No. Zinc reacts with the fatty acids in alkyd and oil paints, a process called saponification, and forms a soapy layer that makes the paint peel. Use acrylic primer and paint on galvanized steel.
How much does it cost to paint a metal roof?
HomeGuide and Angi both put professional metal roof painting at $1.20 to $2.70 per square foot, or roughly $120 to $270 per roofing square. HomeGuide's national average is $2,340. Pressure washing, rust removal and fastener repairs add to that.
How long does metal roof paint last?
Field-applied paint typically needs redoing every 10 to 15 years, according to Angi, and sooner on roofs with poor prep or harsh sun. Factory PVDF finishes last far longer; one manufacturer warrants chalk and fade performance for 35 years.
Do I need to prime a metal roof before painting?
Prime any bare or rusted metal, all galvanized that has never been painted, and PVDF finishes. A sound, well-cleaned SMP finish can often take a DTM acrylic directly, but follow the paint's data sheet. When in doubt, prime.
How long should new galvanized roofing weather before painting?
Sherwin-Williams calls for at least six months of weathering before applying its DTM acrylic to galvanizing. Some roof coating systems allow less with their own primers, so follow the data sheet of the product you are using.
Will painting a metal roof stop leaks?
No. A paint film is only a few mils thick and cannot bridge open seams or loose fasteners. Leaks need repairs plus an elastomeric coating system, typically 20 mils or more, with reinforcement at seams, or a spray-applied membrane.
Can you paint a metal roof yourself?
On a low, walkable roof, yes, if you can meet basic fall protection and handle the washing and prep. Angi estimates DIY saves about $1,000 to $2,000 in labor. Steep, high or fragile roofs are a job for a pro.
Sources
- HomeGuide, metal roof painting cost (2026): homeguide.com/costs/metal-roof-painting-cost
- Angi, cost to paint a metal roof (2026): angi.com/articles/experts-discuss-metal-roof-paint-benefits-cost.htm
- HomeGuide, roof coating cost by type (2026): homeguide.com/costs/roof-coating-or-sealing-cost
- Sherwin-Williams, Pro Industrial DTM Acrylic product data sheet: paintdocs.com (Pro Industrial DTM Acrylic PDS)
- Dunn-Edwards, preparing and painting galvanized substrates: dunnedwards.com technical bulletin
- McElroy Metal, Kynar 500 vs. SMP: blog.mcelroymetal.com
- Metal Sales, PVDF system warranty: metalsales.us.com PVDF warranty
- Karnak, 404 Corrosion Proof and 702 K-Prep data: karnakcorp.com/product/404-corrosion-proof-metal-surface-base-coat
- US Made Supply, acrylic roof coating guide: usmadesupply.com/resources/guides/acrylic-roof-coating
- The Roofing Brief, roof coating types and solar reflectance reference (2026): theroofingbrief.com/roof-coating-types-and-cost
- The Roofing Brief, solar reflectance and SRI reference (LBNL data for bare Zincalume): theroofingbrief.com/roofing-solar-reflectance-sri-reference-2026
- U.S. Department of Energy, cool roofs: energy.gov/energysaver/cool-roofs
- Sheffield Metals, ENERGY STAR roof products sunset: sheffieldmetals.com
- OSHA 29 CFR 1926.501, fall protection: osha.gov 1926.501
- EPA, Lead Renovation, Repair and Painting Program: epa.gov/lead
Metal roofs that stay sealed.
Building owners get a certified ArmorThane applicator who sprays seamless membranes over leaking, corroded metal roofs. Contractors can add metal roof coating with no franchise fee and no royalties.
Protective Roof Coatings & Leak Repair
Flip through the whole brochure right here, or open it full screen on Issuu to share it.
Start your coatings business with ArmorThane.
Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.
- Equipment package matched to your applications
- Hands-on training and applicator certification
- Technical support once you are spraying
Rusty, faded or leaking metal roof? Get the right fix.
Tell us the building type, roof size and pitch, the panel type, and whether it leaks or just looks tired. We will connect you with a certified applicator near you.
- Roof size and pitch
- Panel type and metal
- Rust, chalking or leaks
- Building use and access
More to read on roofing
Short reads from ArmorThane on Issuu. Tap one to open it right here.

















