Skip to content
Polyurea Supplier Near Me

Polyurea Supplier Near Me: Material, Support & Training

Where to buy spray polyurea, what a good supplier should give you, which ArmorThane lines fit your job and how many gallons it will take.

Start a protective coatings business

Spray protective coatings for a living.

ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.

ArmorThane Mobile Coatings Unit trailer hitched to a pickup outside the plant Proportioner, A and B material drums and transfer pumps inside the spray rig Applicator in a protective suit holding a plural-component spray gun in a spray booth Proportioner control panel with heater, pressure balance and cycle counter controls

What comes with itProportioners, guns and complete spray rigs. We build them.

$0
franchise fees or royalties
35+
years in business
50+
countries with applicators
24/7
technical support
1989
Making polyurea in Springfield, Missouri
ArmorThane, manufacturer
NSF 61
AquaShield, for potable water contact
NSF/ANSI 61 approved
1,604
Sq ft one gallon covers at 1 mil
Theoretical, 100% solids
24/7
Tech line for ArmorThane applicators
Included with equipment packages

A polyurea supplier near you is handy when you need a drum set by Friday. A supplier who can tell you why the last set sprayed soft is worth a lot more. Before you compare price per gallon, compare what comes with the gallon: data sheets, a tech line, equipment service and training.

Quick answer

You can buy polyurea from the manufacturer, a regional distributor, an equipment dealer or an online reseller. For two-component, spray-grade material, buy from a source that matches the product to your equipment, sends technical and safety data sheets before you order, and answers a tech call in the middle of a job. ArmorThane makes its polyurea, polyurethane and polyaspartic coatings in Springfield, Missouri. Use the product finder below to match a line to your job and estimate how many gallons it takes.

Buying options

Where polyurea is sold, and what each source gives you

Search "polyurea supplier near me" and you will get a mix of manufacturers, regional distributors, equipment dealers and websites selling kits. All four can be the right answer for someone. What changes from one to the next is who stands behind the material when something goes wrong.

Where you buyWhat you usually getWatch for
Manufacturer, directProduct matched by the people who formulated it, full data sheets, a tech line, and often equipment and training from the same companyMinimum orders and freight terms; ask about both before the first order
Regional distributorStock in your region, several brands under one roof, sometimes will-call pickupWho answers the technical call when a batch acts up: the distributor or the maker
Equipment dealer selling materialMachine, parts and material on one invoiceWhether they know the chemistry or mainly move drums
Online reseller or repackagerSmall kits and quick checkoutRepackaged material, unclear lot history and little support for spray-grade systems
A general comparison of sales channels. Individual distributors and dealers vary; ask each one the questions further down this page.
Does "near me" matter?Less than you might think. Drums move by freight, so distance mostly changes shipping time and cost. Being close helps with pickup and the occasional emergency set. Technical support, consistent material and equipment that matches the product matter on every single job.
The checklist

What a good polyurea supplier should hand you

Price per gallon is easy to compare and easy to be fooled by. A cheaper set that cures soft, peels at the edges or clogs a gun costs more than the savings once you count the redo. These are the things to expect from any supplier, ArmorThane included.

Before you order

Data sheets and SDS

Technical data sheets with processing temperatures, pressures and recommended thickness, plus safety data sheets for both sides. If a supplier cannot send them before the sale, keep looking.

Mid-job

A tech line that answers

Someone who knows the product and the machine, available when you are spraying. ArmorThane applicators have a 24/7 tech line.

Equipment

Material matched to the machine

High-pressure products need heated plural-component equipment. A supplier should ask what you run before recommending a product, and help service it.

Your crew

Hands-on training

Polyurea is unforgiving of bad prep and wrong settings. Training on the actual product and equipment pays for itself on the first few jobs.

Every shipment

Material you can trace

Lot numbers on the drums and paperwork that matches. When something goes wrong, the lot is the first thing the tech line will ask for.

The full job

A system, not just a drum

The right primer, topcoat and prep guidance for the substrate. Many coating failures are prep and primer failures wearing a polyurea label.

Product lines

ArmorThane polyurea by application

Start with the job, then the equipment. The table lists the ArmorThane lines to ask about for each kind of work. It is a starting point for a conversation with our technical team, not a substitute for the data sheet.

ApplicationLines to ask aboutEquipmentNotes
Truck bedliners and vehiclesHighLine 200, HighLine 300, ArmorLiner; ETS-110 on low pressureHigh or low pressureHighLine 200 is ArmorThane's premier bedliner; HighLine 410 is the aliphatic option where color and UV stability matter
RoofingArmorSeal 100 AL, ArmorFlex UVHigh pressureArmorFlex UV is the elastomeric system used on RV roofs
Waterproofing and foundationsHighLine 510H, HighLine 510High pressurePure polyurea, multi-purpose; 510H is used for foundation waterproofing
Potable waterAquaShieldHigh pressureNSF/ANSI 61 approved for direct contact with potable water
Containment and chemical exposureUltraTech, HighLine 510 and other pure polyureasHigh pressureSend the chemical list; the tech team matches resistance to the exposure
Floors and decksArmorFloor, ArmorDeckRolledArmorFloor is an aliphatic polyaspartic; ArmorDeck is a moisture-cured polyurethane deck system with a base and top coat
Industrial, impact and abrasionUltraTech, SureGrip, HardCoat, ArmorShieldHigh pressureSureGrip is a soft polyurea; HardCoat is a rigid hybrid
Pipe liningPLM-100Low pressureArmorThane's specialty pipe lining polyurea
Product names from ArmorThane's catalog. Confirm the system, primer and thickness with technical support and the data sheet before ordering. Tap a column heading to sort.
ArmorThane AquaShield polyurea A and B side drums
AquaShield, ArmorThane's NSF/ANSI 61 polyurea for potable water contact. Every line ships with its own data sheet and SDS.

Browse the full high-pressure ArmorLine catalog and the low-pressure products, or read aromatic vs aliphatic polyurea if you are deciding whether a job needs a UV-stable topcoat.

Equipment

Low pressure or high pressure: buy material your machine can spray

The most expensive mistake a new applicator makes with a supplier is ordering a product their equipment cannot process. Polyurea chemistry is matched to a mix ratio, temperature and pressure. Get those wrong and the material will not cure the way the data sheet promises, no matter how good it is.

Low pressure

Lower cost to get started

ArmorThane's published low-pressure starter package is $25,000. A low-pressure package that runs on standard power is plenty for most new bedliner and RV roof shops.

  • ETS-110, a 1:1 modified polyurea liner
  • STS-200 and STS-300, 2:1 polyurethanes
  • PLM-100 for pipe lining
High pressure

Output for bigger work

A high-pressure system runs about $50,000 and uses a heated plural-component proportioner. Move to it when the jobs need the output and the product range.

  • HighLine and ArmorLine polyureas
  • Pure polyureas such as UltraTech and HighLine 510
  • AquaShield for potable water
Match material to machineTell your supplier what proportioner, hose length and gun you run before you order. If they do not ask, that tells you something too. The polyurea equipment guide compares low and high pressure in detail, and bedliner equipment cost breaks down a shop setup line by line.
Product finder

Match a product line and estimate the gallons

Pick the job and the equipment you run to see which ArmorThane lines to ask about. Then enter the area and thickness to estimate how much material the job takes, and send the whole thing to our team for pricing.

Finder and quantity

Polyurea product finder and gallon estimator

Theoretical gallons = area (sq ft) × thickness (mils) ÷ 1,604, the coverage of one US gallon of 100% solids coating at 1 mil. The loss factor adds overspray, profile and waste; set it to your own history. For products under 100% solids, divide by the volume solids on the data sheet. Drum pairs assume a 1:1 system packaged in 55-gallon A and B drums.

Use your spec or the data sheet
0
Theoretical gallons
0
Gallons with loss
0
55-gal A + B drum pairs

Thickness drives material cost more than anything else on a quote. Polyurea thickness explains typical mils by application, and polyurea cost shows how installed prices come together.

Before you order

Questions to ask any polyurea supplier

Ask these on the first call. The answers tell you how the relationship will go long after the first order ships.

  • How is it priced, and what is the minimum? Per set, per drum or per gallon, and whether freight is included.
  • Freight or pickup? Who books the truck, whether you need a liftgate or a dock, and whether will-call pickup is possible.
  • When will it ship? Get an expected ship date in writing with the quote. Timing depends on the product, the quantity and where you are.
  • How should I store it? Shelf life and storage temperatures for each side. Keep drums sealed and dry; the A side reacts with moisture in the air.
  • What about cold weather? How the material is protected from freezing or crystallizing in transit, and what to do if a drum arrives cold.
  • What else does the system need? Primer, topcoat, cleaner and flush, so you are not stuck halfway through a job.
  • Who do I call when it sprays wrong? A name, a number and the hours they answer.
New to polyurea?If you are still choosing equipment, start there and buy material second. The become an applicator page explains ArmorThane's packages, which include hands-on training, certification and a 24/7 tech line with no franchise fee or royalties.
Material pricing

Buy from the people who make it.

Tell us the job and the equipment you run. We will match the product line, send the data sheets and quote the material.

United States (417) 831-5090 · Canada 780-444-6200

FAQ

Polyurea supplier questions

Where can I buy polyurea coating?

From the manufacturer, a regional distributor, an equipment dealer or an online reseller. For spray-grade, two-component polyurea, buy from a source that matches the product to your equipment, provides technical and safety data sheets and offers technical support. You can request pricing from ArmorThane directly.

Can I buy polyurea without spray equipment?

Most spray polyurea needs plural-component equipment to meter, heat and mix the two sides. Some ArmorThane floor and deck products, such as ArmorFloor and ArmorDeck, are rolled instead of sprayed. If you plan to spray, choose the equipment first and the material second.

How much polyurea do I need for a job?

One US gallon of 100% solids coating covers 1,604 square feet at 1 mil in theory. Multiply area by thickness in mils and divide by 1,604, then add a loss factor. For example, 500 square feet at 60 mils is about 18.7 gallons before loss, or about 21.5 gallons with 15% added.

What is the difference between pure and hybrid polyurea?

Pure polyurea is built on amine-terminated resins, while hybrids blend in polyurethane chemistry to change cost, cure and handling. ArmorThane makes both, including pure polyureas such as UltraTech, HighLine 510 and AquaSafe and hybrids such as HardCoat, ArmorBlast and UltraBlast.

Does ArmorThane sell bedliner material?

Yes. HighLine 200 is ArmorThane's premier bedliner coating, with HighLine 300 and ArmorLiner also used on trucks and vehicles. ETS-110 is a low-pressure option. HighLine 410 is an aliphatic polyurea for jobs that need color and UV stability.

Do I need training to spray polyurea?

Yes. Spray polyurea involves plural-component equipment and isocyanate exposure, which calls for proper respiratory protection and safe work practices. ArmorThane equipment packages include hands-on training, certification and a 24/7 tech line.

AT
Written by the ArmorThane technical team. We have manufactured polyurea, polyurethane and polyaspartic coatings and plural-component spray equipment in Springfield, Missouri since 1989. Product details come from our own catalog and data sheets.

Sources

  1. ArmorThane, ArmorLine high-pressure product catalog and data sheets. armorthane.com/products/armorline-products/high-pressure/
  2. ArmorThane, Polyurea equipment guide. armorthane.com/knowledge-center/polyurea-equipment-guide/
  3. OSHA, Isocyanates safety and health topic. osha.gov/isocyanates
  4. OSHA, Respiratory Protection standard, 29 CFR 1910.134. osha.gov/laws-regs/regulations/standardnumber/1910/1910.134

Material, equipment and training from one manufacturer.

ArmorThane has made polyurea, polyurethane and polyaspartic coatings and the equipment that sprays them in Springfield, Missouri, since 1989. Send your job details or call the team.

United States 417-831-5090 · Canada 780-444-6200
Become an applicator

Start your coatings business with ArmorThane.

Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.

  • Equipment package matched to your applications
  • Hands-on training and applicator certification
  • Technical support once you are spraying
Step 1 of 3

We want to help you find the best ArmorThane applicator for your protective coating project. Please either fill out the request form below or call us toll free at 417-831-5090, any time Monday-Friday, 8:00 a.m. to 5:00 p.m. Central Standard Time.

Pricing out material? Start with the right system.

Tell us the job, the surface and the equipment you run. Our team will match the product line, send the data sheets and quote the material.

  • What you are coating
  • Square footage and target thickness
  • Low- or high-pressure equipment
  • Your city and state or province
Become an applicator

Start your coatings business

Choose “becoming an Applicator / Dealer” and add your details. Our team will call you to talk through markets, equipment and budget.

1Choice
2Contact Information
3Location

Rather talk now? (417) 831-5090 · About the opportunity