Blown-In Insulation: Cost, R-Value & Fiberglass vs Cellulose
What blown-in attic insulation costs in 2026, how fiberglass, cellulose and rockwool compare on real bag charts, and calculators for depth, bags and payback.

Spray foam for a living.
ArmorThane is the one-stop shop for applicators. We make the chemistry, build the equipment, train you hands-on and back you with technical support, with no franchise fees and no royalties. Applicators have come first here since 1989.
- $0franchise fees or royalties
- 35+years in business
- 50+countries with applicators
- 24/7technical support
Blown-in insulation is loose fiber, usually fiberglass, cellulose or rockwool, that a machine blows through a hose onto an attic floor or into closed wall cavities. On an open attic floor it is the cheapest way we know to get to R-49 or R-60, and it fills around wires, trusses and odd framing that batts never fit. We manufacture spray foam, and on most vented attics we still tell homeowners that blown-in insulation over a sealed ceiling is the better buy. This guide compares the three blown-in materials with real bag-chart numbers, shows 2026 costs, explains what separates a good install from a bad one, and gives you two calculators: one for bags and depth, one for savings and payback.
Blown-in insulation costs $1.00 to $2.80 per square foot installed (HomeGuide, 2026), and an average attic job runs $900 to $3,600. Fiberglass is lightest and settles least but needs about 17 inches for R-49; cellulose needs about 15 inches installed for R-49 and slows air better, but weighs more than twice as much; rockwool costs the most and is noncombustible. Air seal the attic floor first: EPA's average 15% heating and cooling savings assumes both air sealing and insulation. If your ductwork or furnace is in the attic, or there is no attic at all, spray foam at the roof deck is usually the better approach.
Blown-in insulation materials
DOE groups these under loose-fill insulation: small pieces of fiber blown into place with special equipment, which makes them good for adding insulation to existing finished areas, odd-shaped spaces and around obstructions.
Blown fiberglass
Chopped glass fiber, about R-2.2 to R-2.9 per inch. Light, does not absorb water, and settles little. Owens Corning's AttiCat chart calls for 17 inches and 25 bags per 1,000 sq ft for R-49, at 0.69 lb per square foot.
Blown cellulose
Recycled paper with fire retardants, about R-3.6 per inch on average (CIMA). Denser, so it resists wind-washing and convection, but settles up to 20%. GreenFiber's chart calls for 15 inches installed (13.5 settled) for R-49. Full details in our cellulose insulation guide.
Blown rockwool
Stone wool fiber, R-3.2 to R-4.1 per inch per HomeGuide, noncombustible, and the most expensive of the three at $1.90 to $4.20 per sq ft installed. Our mineral wool guide covers the material in depth.
Blown-in fiberglass vs cellulose vs rockwool
Bag charts are the honest way to compare blown-in materials, because they tell you the depth, bag count and weight a manufacturer will stand behind for each R-value. Sort any column.
| Material | R per inch | Installed $ / sq ft | Depth for R-49 | Weight at R-49 (lb/sq ft) | Settling | Combustible? |
|---|---|---|---|---|---|---|
| Fiberglass (AttiCat) | R-2.2 to R-2.9 | $1.00–$2.80 | 17 in | 0.69 | Less than cellulose | No |
| Cellulose (GreenFiber) | R-3.1 to R-3.8 | $1.20–$2.80 | 15 in (13.5 settled) | 1.80 | Up to 20% | Treated, passes CPSC test |
| Rockwool | R-3.2 to R-4.1 | $1.90–$4.20 | Per product chart | Per product chart | Less than cellulose | No |
Which one should go in your attic?
- Cold climate, older house with lots of small leaks: cellulose. Its density slows air movement, and Oak Ridge National Laboratory found convection cut loose fiberglass effectiveness by 30% in attics below about 0°F.
- Weak or sagging ceiling, or a leak-prone roof: fiberglass. At R-60 it weighs 0.87 lb per square foot against 2.26 for cellulose, and it does not hold water.
- Fire resistance matters most: rockwool, which is noncombustible, if you can find an installer and accept the price.
- Ducts or furnace in the attic: consider moving the insulation to the roof deck with spray foam instead; see attic foam insulation.
Blown-in attic insulation calculator
Enter the attic floor area and what is up there now. The calculator works out how much R-value you are missing, then shows depth, bags, weight and installed cost for both fiberglass and cellulose using the manufacturers' own coverage charts.
How much blown-in insulation do I need?
Existing R = depth x R per inch (batts 3.2, blown fiberglass 2.5, cellulose 3.2). Depth, bags and weight for the R you add are interpolated from the AttiCat chart (27.5 lb bags) and GreenFiber chart (22.55 lb bags). Cost scales HomeGuide's 2026 prices of $660 to $1,200 per 1,000 sq ft for R-30 and $1,400 to $2,400 for R-60.
Use the bag count on the actual product you buy; every product's chart is different, and the FTC's R-Value Rule ties the R-value claim to installing at least the labeled number of bags at the labeled thickness. For a cellulose-only deep dive, including dense-packing walls, see our cellulose insulation guide.
Blown-in insulation cost
HomeGuide's 2026 national figures are the most detailed public numbers we know of. Your local price depends mostly on attic access, how much air sealing is included, and whether old insulation has to come out first.
$1.00 to $2.80 installed
The typical range for blown-in attic insulation; the full spread runs from about $0.50 to over $5.00. Fiberglass material alone is $0.30 to $1.10 per sq ft and cellulose $0.30 to $1.80.
R-30 vs R-60
Per 1,000 sq ft of attic floor: R-30 runs $660 to $1,200 and R-60 runs $1,400 to $2,400. Most attics land at $900 to $3,600 in total.
Removal and labor
Removing old insulation adds $1 to $2 per sq ft. Labor runs $40 to $80 per hour, and a blowing machine rents for $100 to $200 a day if you do it yourself.
Dense-pack retrofits
Blowing exterior walls costs $1,900 to $7,800 for a typical house, or $1,600 to $4,200 per 1,000 sq ft of wall for dense-pack cellulose.
For context, closed-cell spray foam material alone runs about $0.90 to $1.00 per board foot (HomeGuide), so foaming a roof deck to R-49 costs several times what blowing R-49 on the floor does. That is why we only recommend roof-deck foam when there is a reason: HVAC in the attic, a cathedral ceiling, or a room-over-garage that never gets comfortable. Our attic insulation cost guide runs the numbers on both approaches, and spray foam insulation cost covers foam pricing in detail.
Savings and payback by climate zone
Pick your climate zone and enter what you spend a year on heating and cooling. The estimate uses EPA ENERGY STAR's modeled savings for air sealing plus insulating to 2012 IECC levels, which is about what a good blown-in attic job delivers when the ceiling is sealed first.
What will blown-in insulation save me?
Annual savings = heating and cooling cost x EPA's heating and cooling savings percentage for your zone (7% in zone 1 up to 20% in zone 4C). Payback = project cost / annual savings. DOE attic targets are for an uninsulated attic.
How to get a good blown-in insulation install
Most of the difference between a blown-in job that works and one that does not happens before the hose comes out. Whether you hire it out or rent the machine, this is the order of work.
Inspect and fix the roof and vents first
Look for roof leaks, bath or kitchen fans venting into the attic, and damp or moldy sheathing. Fans must exhaust outdoors. Insulation will not fix a moisture problem and will hide it.
Air seal the attic floor
Seal top plates, plumbing and wiring holes, recessed lights, chases and the hatch. Use fire-rated sealant around flues. This is where much of the comfort and savings comes from.
Baffles, dams and clearances
Install baffles at every rafter bay over the soffits so insulation does not block intake ventilation, dam the hatch, and keep required clearances around chimneys and non-IC-rated fixtures.
Mark the depth
Staple depth rulers across the attic, set to the installed thickness on the bag chart for your R-value.
Blow evenly and count bags
Work from the far eaves back to the hatch, keep the hose low for an even layer, and use at least the chart's bag count for the area. Then get the FTC-required receipt showing area, installed and settled thickness, R-value and bags used.
When blown-in is not the answer
Blown-in insulation assumes a vented attic with a reasonably flat floor. It is the wrong tool for cathedral ceilings and low-slope roofs with no attic (see cathedral ceiling insulation), for rim joists and crawl spaces, and for attics that hold the furnace and ducts, where moving the insulation and air seal to the roof deck with spray foam keeps that equipment inside the conditioned space. For closed walls, dense-pack cellulose is the blown option and injection foam is the alternative.
Furnace or ducts in the attic? Get a roof-deck foam quote.
Tell us the attic size, where the HVAC equipment sits and what insulation is there now. A certified ArmorThane applicator can quote spray foam for the roof deck, and will tell you if blown-in on the floor is the better buy for your house.
Contractors: become an applicator →
Blown-in insulation: common questions
How much does blown-in insulation cost?
HomeGuide's 2026 range is $1.00 to $2.80 per square foot installed, with most attic jobs between $900 and $3,600. By R-value, R-30 runs $660 to $1,200 and R-60 runs $1,400 to $2,400 per 1,000 square feet of attic floor. Removing old insulation adds $1 to $2 per square foot.
Is blown-in insulation better than batts?
On an attic floor, usually yes. Blown-in fills around wiring, truss webs and irregular joists without the gaps and compression that batts leave, and it is easy to reach R-49 or R-60 in one layer. Batts are better in open stud walls and floors, where blown loose-fill has nothing to hold it in place.
Is blown-in fiberglass or cellulose better?
Cellulose has more R per inch (about R-3.6 versus R-2.2 to R-2.9), resists convection losses in very cold attics and slows air movement better. Fiberglass weighs much less (0.69 versus 1.80 lb per sq ft at R-49 on the AttiCat and GreenFiber charts), settles less and does not absorb water. Installed prices are similar.
How deep should blown-in insulation be?
It depends on the material and the target R-value. For R-49, Owens Corning's AttiCat fiberglass chart calls for at least 17 inches and GreenFiber cellulose about 15 inches installed (13.5 inches settled). For R-60 the figures are 20.5 inches of fiberglass and 18.3 inches of cellulose. DOE notes that if you have less than about R-30, roughly 10 to 13 inches, you could probably benefit from adding more.
Can I blow in insulation myself?
Yes, on an accessible attic floor. HomeGuide lists machine rental at $100 to $200 per day. Two people make it far easier: one feeding bags, one on the hose. Do the air sealing, baffles and hatch dam first, wear a respirator, and follow the bag chart. Dense-packing walls takes a more powerful machine and experience.
Does blown-in insulation settle?
Cellulose settles up to 20% in the months after installation, which is why its charts list an installed and a minimum settled thickness. Blown fiberglass settles less. In both cases, installing to the chart's initial thickness with the full bag count delivers the labeled R-value.
Can you blow insulation over existing insulation?
Yes, as long as the existing insulation is dry and clean. The R-values add together. Pull out anything wet, moldy or contaminated by rodents first, and do not cover the soffit vents or recessed lights that are not rated for insulation contact.
How much will blown-in insulation save on energy bills?
EPA ENERGY STAR estimates homeowners save an average of 15% on heating and cooling costs, about 11% of total energy costs, by air sealing and adding insulation, modeled to 2012 IECC levels with a 25% cut in air leakage. The range runs from 7% of heating and cooling in climate zone 1 to 20% in zone 4C.
Other insulation types, compared honestly
Cellulose insulation
Attic and dense-pack wall cellulose, settling, fire treatment and bag math.
Types of insulation
Every major insulation type compared, with a thickness calculator and a selector.
Mineral wool insulation
Stone wool for fire, sound and continuous insulation, with a wall checker.
Sources
- HomeGuide, Blown-in insulation cost (2026): homeguide.com
- HomeGuide, Insulation cost (2026): homeguide.com
- Owens Corning, AttiCat manufacturer's fact sheet and coverage chart: owenscorning.com (cloudfront)
- GreenFiber, loose-fill cellulose fact sheet and coverage chart: homedepot.com
- U.S. DOE Energy Saver, Insulation (recommended attic R-values) and Where to Insulate: energy.gov, energy.gov
- U.S. DOE Energy Saver, Types of Insulation (loose-fill): energy.gov
- EPA ENERGY STAR, air sealing and insulation savings methodology (savings by climate zone): energystar.gov
- Fine Homebuilding via Green Building Advisor, Blown insulation for attics (ORNL 1991 convection finding, settling): greenbuildingadvisor.com
- Cellulose Insulation Manufacturers Association, homeowner facts: cellulose.org
- FTC R-Value Rule, 16 CFR 460.17 installer receipts: ecfr.gov
- U.S. CPSC, 16 CFR Part 1209 cellulose insulation standard: ecfr.gov
Attics insulated the right way.
Homeowners get a certified ArmorThane applicator who will say when blown-in is the better buy and when the roof deck needs foam. Contractors can add spray foam with no franchise fee and no royalties.
Start your coatings business with ArmorThane.
Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.
- Equipment package matched to your applications
- Hands-on training and applicator certification
- Technical support once you are spraying
Blown-in on the floor or foam on the roof? Get an honest answer.
Tell us the attic size, where the furnace and ducts are, and what insulation is there now. We will connect you with a certified applicator for spray foam where it fits.
- Attic floor area and access
- HVAC equipment in the attic?
- Existing insulation depth
- Ice dams, hot rooms or drafts
More in Spray foam & insulation
Spray foam & insulationSpray Foam Insulation Contractors
Spray foam & insulationSpray Foam Insulation Cost
Spray foam & insulationSpray Foam Insulation Problems
Spray foam & insulationSpray Foam Insulation Training
Spray foam & insulationSpray Foam Machine
Spray foam & insulationSpray Foam PPE
Spray foam & insulationSpray Foam Proportioner
Spray foam & insulationSpray Foam R-Value Guide








