Skip to content
Spray Foam Roof Granules

Spray Foam Roof Granules: When They Pay Off

Why contractors embed roofing granules in the topcoat of a spray foam roof, what they protect against, the trade-offs, and how they are applied.

Busy Builder Standing at Rooftop of Constructi Utc

Start a spray foam business

Spray foam for a living.

ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.

ArmorThane Mobile Coatings Unit trailer hitched to a pickup outside the plant Proportioner, A and B material drums and transfer pumps inside the spray rig Applicator in a protective suit holding a plural-component spray gun in a spray booth Proportioner control panel with heater, pressure balance and cycle counter controls

What comes with itProportioners, guns and complete spray rigs. We build them.

$0
franchise fees or royalties
35+
years in business
50+
countries with applicators
24/7
technical support
UV
Shade the coating from sunlight
SPFA guidance
Hail
Added impact and puncture resistance
Industry practice
Traffic
Better wear surface for foot traffic
Industry practice
Wet coat
Broadcast into the final, wet coat
Manufacturer instructions

A spray polyurethane foam roof is only as long-lived as the coating that protects the foam. Embedding roofing granules in the final coat adds a mineral armor layer on top of that coating. It is a common upgrade in hail country, on roofs with heavy foot traffic, and where birds peck at foam. It also has costs: weight, lower reflectivity on some roofs and more work to recoat later. Here is how to decide.

Quick answer

Spray foam roof granules are mineral or ceramic-coated roofing granules broadcast into the wet final coat of an SPF roof coating. They improve UV, hail, puncture and foot-traffic resistance and can extend the time between recoats. The trade-offs are added weight and cost, a rougher surface that holds dirt, possible loss of reflectivity compared with a smooth white coating, and more prep when the roof is recoated. They are worth it on roofs that face hail, traffic or birds.

Start here

Why add granules to a foam roof?

Protect

UV shielding

Granules shade the elastomeric coating so it erodes more slowly.

Armor

Hail and puncture

The mineral layer spreads impact and resists punctures from hail, dropped tools and debris.

Wildlife

Bird and traffic damage

A granulated surface discourages birds from pecking foam and holds up under foot traffic.

Weigh it

Granules: pros and cons

FactorWith granulesSmooth coating only
Impact and hail resistanceHigherLower
Foot trafficBetter wear surfaceUse walkway pads
ReflectivityCan be lower unless white or reflective granules are usedHighest with a white topcoat
Dirt pickupRougher surface can hold dirtEasier to keep clean
InspectionHarder to spot coating defectsEasy to inspect
RecoatingRemove loose granules and primeClean and recoat
CostAdded material and laborLower
Do it right

How granules are applied

  1. Spray the foam

    Apply SPF to the specified thickness and slope.

  2. Base coat

    Apply the elastomeric base coat the same day the foam is sprayed when possible.

  3. Final coat

    Apply the topcoat at full specified thickness.

  4. Broadcast granules

    While the topcoat is wet, broadcast granules evenly at the rate the coating maker specifies.

  5. Cure and sweep

    After cure, sweep or blow off loose granules.

  6. Inspect

    Check for bare spots and recoat as needed.

Field noteGranules do not replace coating thickness. A thin coating under a heavy layer of granules still fails early. Measure the coating first.
Where it fits

When granules are worth it

Recommended

Hail-prone regions

Roofs in areas with frequent hail.

Recommended

Heavy traffic roofs

Rooftop equipment and frequent service visits.

Recommended

Bird pressure

Roofs where birds peck exposed foam.

Optional

Cool-roof goals

Use white or reflective granules, or keep a smooth white coating if reflectivity is the priority.

Related: spray foam roofing, spray foam roofing cost and polyurethane roof coating.

Spray foam roofing

Foam roofs built to last.

A certified ArmorThane applicator can spray, coat and granulate your foam roof, or recoat an existing one.

Contractors: become an ArmorThane applicator

FAQ

Spray foam roof granules questions

Why put granules on a spray foam roof?

To add UV, hail, puncture and foot-traffic protection to the coating that protects the foam, and to discourage birds.

Do granules make a foam roof last longer?

They can extend coating life by shielding it from UV and impact, but only when the coating underneath is applied at full thickness.

Do granules reduce roof reflectivity?

Standard colored granules can lower reflectivity compared with a smooth white coating. White or reflective granules reduce that effect.

How are granules applied to a foam roof?

They are broadcast evenly into the final coating while it is still wet, then loose granules are removed after cure.

Can you recoat a foam roof with granules?

Yes. Loose granules are removed, the surface is cleaned and primed as needed, and a new coating is applied.

AT
Written by the ArmorThane technical team. We have manufactured polyurea, polyurethane and polyaspartic coatings, spray foam and plural-component spray equipment in Springfield, Missouri since 1989. Follow the coating manufacturer instructions for granule type and broadcast rate.

Sources

  1. Spray Polyurethane Foam Alliance, SPF roofing guidance. sprayfoam.org
  2. Cool Roof Rating Council, roof product ratings. coolroofs.org

Armor your foam roof.

Building owners get a certified ArmorThane applicator for spray foam roofing. Contractors can add foam roofing with our equipment and training, with no franchise fee and no royalties.

United States 417-831-5090 · Canada 780-444-6200
Cover of the ArmorThane brochure: Protective Roof Coatings & Leak Repair
Brochure

Protective Roof Coatings & Leak Repair

Flip through the whole brochure right here, or open it full screen on Issuu to share it.

Become an applicator

New foam roof or recoat? Get it quoted.

Tell us the roof size and condition. We will connect you with a certified applicator.

  • New SPF roof or recoat
  • Approximate square footage
  • Hail, traffic or bird issues
  • Current roof type
Step 1 of 3
Become an applicator

Start your coatings business

Choose “becoming an Applicator / Dealer” and add your details. Our team will call you to talk through markets, equipment and budget.

1Choice
2Contact Information
3Location

Rather talk now? (417) 831-5090 · About the opportunity