Efflorescence: Causes, Removal & Prevention
What the white deposits on concrete, block and pavers mean, how to clean them without making it worse, and how to stop them coming back.
Start a protective coatings business
Spray protective coatings for a living.
ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.
- $0
- franchise fees or royalties
- 35+
- years in business
- 50+
- countries with applicators
- 24/7
- technical support
Efflorescence is the white, powdery or crusty deposit that shows up on concrete, block, brick and pavers. It is salt left behind when water moves through the masonry and evaporates at the surface. On its own it is mostly cosmetic. What it tells you is not: water is getting into the concrete and moving through it. Clean the efflorescence without dealing with the water and it comes back, and if you coat over it, the coating is what fails.
Brush it off dry first; most efflorescence is water-soluble and much of it weathers away on its own. If it persists, rinse in warm, dry weather. Hard white crust that does not brush off is usually calcium carbonate and needs a dilute acid or a proprietary efflorescence cleaner on a pre-wetted surface, in small sections, then a thorough rinse. Then find the water source: missing flashing, a downspout, soil against a wall, rising damp in a slab. Seal with a breathable water repellent only after the surface is clean and dry.
What efflorescence is, and why it forms
The Concrete Masonry and Hardscapes Association (CMHA, formerly NCMA) defines efflorescence in TEK 08-03A as a deposit of soluble salts and bases, usually white, on the surface of masonry or concrete. The Brick Industry Association's Technical Note 23A says the same thing about brick. Both list three conditions that have to happen together:
Soluble salts in or touching the masonry
Sodium, potassium and calcium compounds from cement, mortar, grout, soil, deicers or seawater. BIA lists sulfates and carbonates of sodium, potassium, calcium, magnesium and aluminum as the most common.
Water to dissolve them
Rain, groundwater, irrigation, condensation, or leftover construction water.
A force to move the solution
Evaporation at the surface or hydrostatic pressure pushing water through the concrete.
Take away any one of the three and efflorescence stops. In practice, water is the only one you can control.
The calcium carbonate problem
Some efflorescence is simple soluble salt that brushes or rinses off. The stubborn kind starts as calcium hydroxide, a byproduct of cement hydration. It is soluble, so water carries it to the surface, where it reacts with carbon dioxide in the air to form calcium carbonate, which is only slightly soluble. That is why some deposits wash away in the next rain and others build into a hard white crust or a "lime run" streak below a crack.
Why it is worse in winter
TEK 08-03A notes that efflorescence shows up more in cooler, wetter months, because slow evaporation leaves the salts on the surface. In summer, water evaporates fast enough that less salt is deposited on the face. BIA calls efflorescence within the first year of construction "new building bloom", normal drying of construction water, usually uniform across a wall. It typically fades on its own.
Is it efflorescence? Find the water source
White deposits are not always efflorescence, and the pattern usually points straight at the water. Two quick tests help: a drop of water (soluble salts dissolve and disappear) and a few drops of vinegar (calcium carbonate fizzes). Mold smears and often has color; chalking paint rubs off on your finger as paint-colored powder.
Efflorescence identifier and source finder
Matches the deposit type to a removal method and the location and pattern to the most likely water source.
How to remove efflorescence
Always start with the gentlest method and work up. TEK 08-03A lists them in order: dry brushing, then flushing with water, then light brush sandblasting, then dilute acid. BIA adds that water washing should only be done in warm, dry weather, so the surface dries quickly and does not pull more salt up.
| Method | Aggression (1–5) | Removes | Risks | Use on colored units? |
|---|---|---|---|---|
| Dry stiff-bristle brush | 1 | Loose soluble salts | Minimal | Yes |
| Brush plus water rinse | 2 | Soluble salts | Adds water; do it in warm, dry weather | Yes |
| Proprietary efflorescence cleaner | 3 | Salts and light carbonate | Follow label; test a patch | Per label |
| Light brush sandblast | 4 | Stubborn deposits | Can roughen or open the surface | Test first |
| Dilute muriatic acid, 5–10% | 5 | Calcium carbonate crust | Etches, can blotch color; hazardous | Only at 2% |
| High-pressure washing | 4 | Surface deposits | Drives water in; can bring it back | Low pressure only |
The acid method, done safely
Test a hidden spot
Acid can lighten or blotch colored concrete and pavers. Try a small area first and let it dry before you judge it.
Pre-wet with clean water
TEK 08-03A calls for saturating the surface first so the acid stays on top instead of soaking in.
Work in small sections
Treat no more than about 4 sq ft at a time, wait about 5 minutes, then scrub with a stiff brush.
Flush thoroughly
Rinse with plenty of clean water so no acid or dissolved salt is left in the surface.
Wait before sealing or painting
TEK 08-03A suggests letting the surface weather for at least a month after acid cleaning before painting.
Efflorescence cleaning and acid dilution planner
Mixing ratios get garbled on job sites. This planner turns the TEK 08-03A percentages into parts of water per part of commercial muriatic acid, works out how much of each to mix for the area, and how many 4 sq ft sections the job breaks into.
Acid solution and section planner
Solution % here means percent commercial muriatic acid by volume (10% = 1 part acid to 9 parts water). Volume needed = area / coverage rate you enter. Sections = area / 4 sq ft.
If the planner says you need a lot of acid, stop and reconsider. Large areas of efflorescence almost always mean a large water problem, and cleaning will not last. Dry brushing every few weeks through one wet season while you fix the water is often the smarter path.
White deposits keep coming back? Fix the water, then protect it.
Certified ArmorThane applicators test concrete moisture, repair cracks and apply waterproofing and floor systems suited to damp slabs and walls.
Contractors: become an applicator →
Preventing efflorescence
Since salts are already in every cementitious material, prevention is about water. TEK 08-03A's recommendations for masonry walls include flashing at parapets, lintels and the base of walls, tooled concave or V-shaped mortar joints on weather-exposed faces, integral water-repellent admixtures in new units and mortar, and clear surface water repellents, which it says can be effective for up to 10 years.
Keep groundwater off the wall
Regrade so soil falls away, extend downspouts, and repair cracks. On the outside, a waterproofing membrane; on block walls, a sound parge coat. Our parging guide covers that. For bigger leaks see basement waterproofing cost.
Stop water at the top and joints
Caps, copings, flashing and sealed joints. A breathable masonry sealer (silane or siloxane type) cuts water absorption without trapping vapor.
Good base drainage, then seal
Efflorescence on new pavers is common and fades with time. Clean, let it dry, then apply a paver sealer once the bloom stops.
Vapor retarder and drainage
Slabs on grade without a vapor retarder pull ground moisture up all year. That cannot be fixed from the top with a sealer alone; it needs a coating system designed for moisture.
Efflorescence and floor coatings
This is where efflorescence costs real money. A garage or basement floor with white deposits is a slab with moisture moving up through it. Put an epoxy, polyaspartic or polyurea coating on top without addressing that, and the water and salts collect under the film. You get blisters, white haze under clear coats, and coating that peels in sheets. We see it most on older slabs poured without a vapor retarder.
Test before you coat
- Plastic sheet test (ASTM D4263): tape an 18 x 18 in sheet of plastic to the slab, wait at least 24 hours, and look for darkening or condensation. It is a yes or no screen, not a number.
- Calcium chloride test (ASTM F1869): measures moisture vapor emission over a 60 to 72 hour test.
- In-slab relative humidity (ASTM F2170): a probe set at 40% of slab depth for slabs drying from one side, read after 24 hours of equilibration. Neither ASTM standard sets a pass mark; the coating maker does, and typical acceptance runs roughly 75 to 80% RH.
If the numbers are high, the options are a moisture-mitigating primer system rated for the reading, or a different floor treatment. Grinding off the efflorescence alone is not a fix. Our garage floor coating guide covers system choice, and concrete waterproofing covers walls and below-grade slabs.
Prep when efflorescence is present
Mechanical grinding removes the deposit and the weak, salt-laden paste under it, which acid etching does not reliably do. Vacuum, then check for fresh bloom after a day or two; if it reappears quickly, moisture is still moving. Repair cracks that carry water first (see concrete crack repair), because white streaks under a crack mean the crack itself is the path.
Efflorescence questions
Is efflorescence harmful?
Usually not to the concrete or masonry itself; the Brick Industry Association describes it as normally harmless. It is a sign of water moving through the material, though, and salts that crystallize inside the surface can cause spalling. It is also a common cause of coating and paint failures.
Will efflorescence go away on its own?
Often, yes. New building bloom in the first year typically fades as construction water dries out, and most soluble salts wash or weather off. If it keeps returning after the first year, there is an ongoing water source to find.
Does vinegar remove efflorescence?
Vinegar is a weak acid and can dissolve light calcium carbonate deposits, and it is useful as a test because carbonate fizzes. For heavier crust, TEK 08-03A refers to dilute muriatic acid at 5 to 10 percent, or 2 percent on colored units, used on a pre-wetted surface and rinsed well. Proprietary efflorescence cleaners are gentler alternatives.
Should I pressure wash efflorescence?
Be careful. Dry brushing is the recommended first step. Washing adds water, and BIA advises doing it only in warm, dry weather so the surface dries fast. High pressure can also open the surface and drive water deeper.
Is efflorescence a sign of a foundation problem?
It is a sign of moisture, not of structural failure. Efflorescence along a crack shows that water is getting through that crack. Have a professional look if you also see widening cracks, bowing walls or active leaks.
Can I seal over efflorescence?
Clean it off and let the surface dry first, and fix the water source if you can. Sealing over salt traps it, and non-breathable sealers on damp walls tend to blister. Breathable silane or siloxane water repellents are the usual choice for walls and pavers.
How is efflorescence different from mold?
Efflorescence is crystalline, usually white, and dissolves in water or fizzes with vinegar. Mold looks fuzzy, often has color, may smell musty, and smears rather than crumbles. Both need moisture, so finding the source fixes both.
Sources
- CMHA (formerly NCMA), TEK 08-03A Control and removal of efflorescence: cmha.org TEK 08-03A
- Brick Industry Association, Technical Note 23A Efflorescence: causes and prevention: gobrick.com/media/file/23a-tn23a.pdf
- HASA, Muriatic acid safety data sheet: hasa.com/.../Muriatic Acid - Safety Data Sheet.pdf
- Tnemec, 3 ways to test concrete moisture (ASTM D4263): tnemec.com/remedy-index-page/3-ways-test-concrete-moisture
- IFTI, ASTM F2170 vs F1869 moisture testing: ifti.com/concrete-moisture-testing-astm-f2170-vs-f1869-guide
Stop the water, and the white goes with it.
Property owners get a certified ArmorThane applicator who tests moisture and applies the right waterproofing or floor system. Contractors can add these services with no franchise fee and no royalties.
Start your coatings business with ArmorThane.
Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.
- Equipment package matched to your applications
- Hands-on training and applicator certification
- Technical support once you are spraying
White deposits on your concrete? Get the water problem solved.
Tell us where the efflorescence is (basement wall, garage floor, exterior wall, pavers), how big the area is, and whether you plan to coat it. A certified applicator near you will follow up.
- Basement walls and floors
- Garage floors before coating
- Exterior block, brick and retaining walls
- Moisture testing before any coating















