Skip to content
Modified Bitumen Roof

Modified Bitumen Roof: Repair, Restore or Replace

How torch-down, cold-applied and self-adhered mod bit roofs work, what they cost, how they fail, and when a coating can buy another decade.

Applicator coating a flat roof

Start a roof coating business

Spray roofs for a living.

ArmorThane sets you up to do this work, and you own the business. We make the chemistry, build the rigs, train you hands-on and answer the phone when a job gets difficult. You pay no franchise fee and no royalties. It has been that way since 1989.

ArmorThane Mobile Coatings Unit trailer hitched to a pickup outside the plant Proportioner, A and B material drums and transfer pumps inside the spray rig Applicator in a protective suit holding a plural-component spray gun in a spray booth Proportioner control panel with heater, pressure balance and cycle counter controls

What comes with itProportioners, guns and complete spray rigs. We build them.

$0
franchise fees or royalties
35+
years in business
50+
countries with applicators
24/7
technical support
$4–$8
Per sq ft installed, about $6 on average
HomeAdvisor, updated June 20, 2026
30 yrs
Typical lifespan of a modified bitumen roof
HomeAdvisor, June 2026
~$400
Average cost of a flat roof repair
HomeAdvisor, June 2026
$1–$4
Per sq ft for most coating restorations
HomeGuide 2026, via ArmorThane

A modified bitumen roof is asphalt upgraded with rubber or plastic modifiers and built into reinforced sheets at the factory. It's the descendant of the old built-up roof, with the same waterproofing chemistry, but a crew can install it in two plies instead of building it up by hand. It goes down hot with a torch, cold in adhesive, or as a peel-and-stick sheet.

Quick answer

Modified bitumen roofing costs $4 to $8 per square foot installed, about $6 on average, and lasts around 30 years, according to HomeAdvisor. Most problems show up as granule loss, blisters, open laps and failing flashings. If the roof is still dry underneath, repairs plus an acrylic, silicone or aluminum coating can add years for roughly $1 to $4 per square foot. Wet insulation or cracking across the whole roof means replacement.

Roof inspection

Find a certified applicator by ZIP code

Granules in the gutters, a blister that keeps growing, a lap that's starting to lift: those are the moments to have someone look. Send your ZIP and a few details and the nearest certified ArmorThane applicator will follow up. ArmorThane makes coatings and spray equipment; we don't install roofing sheets.

Applicator match

Request a mod bit roof inspection

Enter your ZIP or postal code and a few details. We route the request to the nearest certified ArmorThane applicator; nothing is shared with anyone else.

Enter your ZIP or postal code to see where your request goes.

How it's installed

Torch-down, cold-applied and self-adhered

Most modified bitumen roofs are two-ply systems: a base sheet fastened or adhered to the insulation or deck, and a cap sheet on top. The cap sheet usually carries a surface of mineral granules that shields the asphalt from sunlight. What separates the three types is how the sheets are bonded.

Heat-applied

Torch-down

The crew heats the back of the sheet with a propane torch until the asphalt melts, then rolls it in. It bonds well and fuses the laps, but an open flame near wood nailers, walls and penetrations is a fire risk, so some owners now ask for flame-free details.

Flame-free

Cold-applied

Sheets are set into a cold adhesive that's troweled or sprayed on. There's no torch and less odor than hot asphalt, but the adhesive needs time and decent weather to cure, and the laps depend on careful rolling.

Peel-and-stick

Self-adhered

A factory adhesive on the back of the sheet bonds once the release film comes off. It's the cleanest install and common on smaller and residential low-slope roofs. It needs a clean, primed surface and warm enough weather to grab.

SBS: rubber-modified

Styrene-butadiene-styrene gives the asphalt a rubbery stretch, so SBS sheets stay flexible in cold weather and handle building movement well. They can be torched, mopped in hot asphalt, set in cold adhesive or made self-adhered.

APP: plastic-modified

Atactic polypropylene makes a stiffer, plastic-like sheet that holds up well to heat and sunlight. APP is almost always torch-applied, which is why "torch-down" and APP often get used as if they meant the same thing.

Modified bitumen roofing cost

What it costs next to other flat roofs

HomeAdvisor's June 2026 flat roof guide puts modified bitumen at $4 to $8 per square foot installed, with most jobs around $6. That makes it one of the lower-priced flat roof systems per square foot, with an expected life of about 30 years.

Modified bitumen
$4–$8
Built-up (tar and gravel)
$4–$10
EPDM rubber
$4–$13
TPO
$4–$14

Installed cost per sq ft from HomeAdvisor's flat roof cost guide, updated June 20, 2026. Bars show the top of each range.

For a whole roof, HomeAdvisor puts a flat roof replacement at $3,331 to $11,558, averaging $7,433, which reflects smaller, mostly residential roofs. On a 10,000 sq ft commercial roof, $4 to $8 per square foot is $40,000 to $80,000 before any tear-off surprises. These are the things that move a mod bit bid:

  • Layers to remove. Tearing off one old roof costs less than tearing off two or three.
  • Wet insulation. Every wet board found during tear-off is added cost.
  • Install method. Torch, cold adhesive and self-adhered sheets differ in labor, material and safety precautions.
  • Details. Curbs, drains, walls and penetrations take far more labor per foot than open field.
  • Access. Roof height, hoisting and staging show up in every line.

Weighing other systems? Compare TPO roofing, EPDM roofing and PVC roofing.

Warning signs

How to read an aging mod bit roof

Modified bitumen ages in a predictable order. The granules go first, then the exposed asphalt dries and cracks, then laps and flashings open up. Catching it at the first or second stage is what keeps a coating on the table.

What you seeWhat it meansUsual fixCoating still an option?
Granule loss: bare or shiny patches, granules in guttersSunlight is reaching the asphalt and drying it outClean and coat to replace the lost UV protectionYes, often the best time to coat
BlistersTrapped moisture or air between plies expands in the heatCut out, dry and patch with compatible sheetYes, after repairs
Alligatoring: a cracked, scaly surfaceAsphalt or an old coating has oxidized and shrunkShallow cracks are primed and coated; cracks into the reinforcement need repairDepends on depth
Open lapsThe bond at the overlap failed from age, poor torching or movementRe-heat and re-seal, or strip in with new membraneYes, after repairs
Flashing pulling awaySheet shrinkage or failed base flashings at walls, curbs and edgesRebuild flashings and terminationsYes, after repairs
Ponding waterLow spots from deck deflection, crushed insulation or slow drainsImprove drainage; use a coating rated for pondingYes, with the right coating
Soft spots underfootWet or crushed insulationCore cut, then cut out and replace wet areasOnly once it's dry
A roof walk and a few core cuts sort most mod bit roofs into one of these rows.

If water is already coming in, see commercial roof leak repair and ponding water on flat roofs.

Estimator

Repair, restore or replace?

Check the problems you can see from a roof walk or photos. The estimator weighs them against the roof's age and any wet area, prices both paths and suggests the coating family an applicator would likely start with.

Mod bit roof estimator

What your roof is telling you

Replacement uses HomeAdvisor's $4–$8 per sq ft installed range (June 2026); tearing off old layers may be extra. Restoration uses $1–$4 per sq ft, moving to $4.50–$8 when three or more problems are checked or any area is wet (HomeGuide 2026, via our roof coating cost guide). The verdict is a rule of thumb, not an inspection.

Soft spots or core-cut results.
What you see (check all that apply)
—
New mod bit roof
—
Repairs + coating
—
Rule-of-thumb verdict
—
Coating to start with

    Restoration

    Coatings that work on modified bitumen

    Granulated torch-down roofs are commonly restored with acrylic, silicone or aluminum coatings, and asphalt-based coatings are the budget option. Each has a lane. Installed ranges are from our roof coating cost guide.

    CoatingInstalled per sq ftGood atWatch for
    Asphalt and aluminum$1.00–$2.50 (asphalt)Low-cost renewal; aluminum versions add reflectivityThinner films that need recoating sooner
    Acrylic$0.50–$3.00Bright white surface on roofs that drain wellNot for ponding water; needs a bleed-blocking primer on asphalt
    Silicone$1.50–$4.50Ponding-prone roofs and strong UV exposureSlick when wet; future recoats generally need silicone
    Polyurethane$1.50–$4.00Foot traffic and impactAromatic base coats need a UV-stable topcoat
    Sprayed polyureaPriced per projectThick, seamless, fast-curing film for hail, traffic and pondingNeeds a trained crew and a plural-component rig
    Ranges are national installed averages; a local bid depends on prep and repairs. Tap a column heading to sort.
    Bleed-throughAsphalt can migrate into a fresh white coating and stain it brown. On smooth or bare mod bit, the coating maker usually calls for a bleed-blocking primer or base coat. If a bid doesn't mention it, ask.
    Prep

    Prep that makes a coating last

    Prep is roughly 30 to 50 percent of a coating job. On mod bit, that money buys the steps below, in this order. Skip one and the coating fails at the weak spot nobody fixed.

    1. Moisture survey and core cuts

      Confirm the insulation is dry and mark any wet areas. A coating over wet insulation traps the water.

    2. Replace wet insulation and patch

      Wet boards come out, new ones go in, and the opening is closed with compatible mod bit sheet.

    3. Repair blisters, laps and flashings

      Blisters are cut and patched, open laps sealed or stripped in, flashings rebuilt and loose edge metal reset.

    4. Clean

      Pressure washing removes loose granules, dirt and growth. The roof dries completely before anything goes on.

    5. Prime where the data sheet calls for it

      Bleed-blocking primer on asphalt, and an adhesion test on any old coating that will stay in place.

    6. Reinforce details, then coat the field

      Seams, penetrations and flashings get reinforced coating first. The field goes on at the specified thickness, checked with a gauge.

    If you already install mod bit, coating restorations sell to the same buildings and the same owners, often years before they're ready to re-roof. ArmorThane's applicator program has no franchise fee or royalties and includes hands-on training, certification and a 24/7 tech line. See also starting a roofing company.

    Mod bit restoration

    See if your roof can be coated, not replaced.

    A certified ArmorThane applicator can core the roof, list the repairs and put the coating system, thickness and price in writing.

    Learn more about roof restoration

    FAQ

    Modified bitumen roof questions

    What is a modified bitumen roof?

    A modified bitumen roof is a flat or low-slope roof made of reinforced asphalt sheets modified with rubber (SBS) or plastic (APP). It's usually installed in two layers, a base sheet and a granulated cap sheet.

    How much does a modified bitumen roof cost?

    HomeAdvisor's June 2026 guide puts modified bitumen at $4 to $8 per square foot installed, about $6 on average. Tear-off, wet insulation, flashings and access can push a bid higher. Coating restoration of a sound roof typically runs $1 to $4 per square foot.

    How long does a modified bitumen roof last?

    HomeAdvisor puts the typical lifespan at about 30 years. Roofs that lose their granules early, hold ponding water or have poorly sealed laps can fall short, and a timely coating can extend the life of a roof that's still dry underneath.

    What's the difference between SBS and APP modified bitumen?

    SBS is rubber-modified, stays flexible in cold weather and can be torched, mopped, cold-applied or self-adhered. APP is plastic-modified, stiffer, handles heat and sunlight well and is almost always torch-applied.

    Can you coat a modified bitumen roof?

    Yes. Granulated mod bit is commonly restored with acrylic, silicone or aluminum coatings once wet insulation, blisters, open laps and flashings are repaired. On bare asphalt, a bleed-blocking primer keeps the asphalt from staining a white coating.

    Is a torch-down roof the same as modified bitumen?

    Torch-down is one way to install modified bitumen: the sheets are heated with a propane torch and rolled into place. Modified bitumen can also be set in cold adhesive or installed as a self-adhered sheet.

    About these numbersCosts are national installed averages from the guides below; local prices vary. Certified applicators are independent local businesses that set their own prices.
    AT
    Written by the ArmorThane technical team. We have manufactured polyurea, polyurethane and polyaspartic coatings and plural-component spray equipment in Springfield, Missouri, since 1989. Roof system costs come from HomeAdvisor; coating bands come from our roof coating cost guide.

    Sources

    1. HomeAdvisor, Flat roof cost guide (updated June 20, 2026): installed cost by system, lifespan, replacement and repair averages. homeadvisor.com
    2. ArmorThane, Roof coating cost guide (HomeGuide 2026 installed ranges, prep share and commercial restoration bands). armorthane.com/roof-coating-cost
    3. ArmorThane, Roof coating guide. armorthane.com/knowledge-center/roof-coating-guide

    Granules going, roof still dry? That's the time to coat.

    A certified ArmorThane applicator can repair the problem spots and restore a modified bitumen roof for a fraction of a tear-off.

    United States 417-831-5090 · Canada 780-444-6200
    Cover of the ArmorThane brochure: Protective Roof Coatings & Leak Repair
    Brochure

    Protective Roof Coatings & Leak Repair

    Flip through the whole brochure right here, or open it full screen on Issuu to share it.

    Become an applicator

    Start your coatings business with ArmorThane.

    Tell us what you want to spray and where you are. An ArmorThane specialist will walk you through the equipment, chemicals, training and startup cost for the work you want to do.

    • Equipment package matched to your applications
    • Hands-on training and applicator certification
    • Technical support once you are spraying
    Step 1 of 3

    We want to help you find the best ArmorThane applicator for your protective coating project. Please either fill out the request form below or call us toll free at 417-831-5090, any time Monday-Friday, 8:00 a.m. to 5:00 p.m. Central Standard Time.

    Have your mod bit roof looked at by a pro.

    Tell us about the roof and a certified ArmorThane applicator near you will follow up to inspect it and quote repairs or a coating restoration.

    • Building address or ZIP code
    • Approximate roof size
    • Roof age and install type, if known
    • Photos of blisters, bare spots or leaks
    Become an applicator

    Start your coatings business

    Choose “becoming an Applicator / Dealer” and add your details. Our team will call you to talk through markets, equipment and budget.

    1Choice
    2Contact Information
    3Location

    Rather talk now? (417) 831-5090 · About the opportunity